What causes motor switchover fault during running in Inovance MD280NT2.2GB?
A motor switchover fault during running occurs when motor switchover is performed via terminal during running of the AC drive. Perform motor switchover after the AC drive stops.
How to resolve initial position fault on Inovance Inverter?
An initial position fault may occur because the motor parameters are not set based on the actual situation. Check whether the motor parameters are set correctly and whether the setting of rated current is too small.
Why does Inovance MD280NT2.2GB report overcurrent and overvoltage frequently?
If your Inovance AC drive frequently reports overcurrent and overvoltage, it could be due to improperly set motor parameters, improper acceleration/deceleration time, or load fluctuations. You can try setting the motor parameters in group F1 again and setting a proper acceleration/deceleration time.
How to fix current detection fault in Inovance MD280NT2.2GB?
A current detection fault in your Inovance Inverter may be due to a faulty HALL device or a faulty drive board. To resolve this, replace the faulty HALL device or the faulty drive board.
How to fix overcurrent during acceleration in Inovance MD280NT2.2GB?
Overcurrent during acceleration in your Inovance Inverter may be due to several reasons: a grounded or short-circuited output circuit, too short acceleration time, inappropriate manual torque boost or V/F curve, low voltage, startup operation performed on a rotating motor, a sudden load during acceleration, or an AC drive model of too small power class. To resolve this, you can: * Replace external faults. * Increase the acceleration time. * Adjust the manual torque boost or V/F curve. * Adjust the voltage to the normal range. * Select rotational speed tracking restart or start the motor after it stops. * Remove the added load. * Select an AC drive of a higher power class.
What to do if Inovance MD280NT2.2GB Inverter has a control power supply fault?
If your Inovance Inverter has a control power supply fault, it could be because the input voltage is not within the allowable range or the input voltage is not stable, causing the bus voltage to jump frequently around the undervoltage threshold. You can try to adjust the input voltage to the allowable range and wait at least five minutes after power failure until the input voltage becomes normal, and then power on the AC drive again.
What to do if Inovance MD280NT2.2GB reports power output phase loss?
If your Inovance Inverter reports a power output phase loss, it could be due to a faulty cable connecting the AC drive and the motor, the AC drive's three-phase outputs being unbalanced when the motor is running. Try to replace external faults and check whether the motor three-phase winding is normal.
What causes power input phase loss in Inovance MD280NT2.2GB?
Power input phase loss in your Inovance Inverter may be due to the three-phase power input being abnormal. You can try to replace external faults.
What causes fast current limit timeout on Inovance MD280NT2.2GB?
A fast current limit timeout on your Inovance Inverter may be due to: the acceleration/deceleration time being too short, inappropriate manual torque boost or V/F curve, startup operation performed on the rotating motor, or the load being too heavy. To address this: * Increase the acceleration/deceleration time. * Adjust the manual torque boost or V/F curve. * Use rotational speed tracking startup or perform startup after the motor stops. * Use an AC drive of a higher power class.
What to do if Inovance MD280NT2.2GB displays motor overload?
If your Inovance Inverter indicates a motor overload, possible causes include FB-01 being set improperly, the load being too heavy or locked-rotor occurring on the motor, or the AC drive model being of too small a power class. To resolve this: * Set FB-01 correctly. * Reduce the load and check the motor and mechanical conditions. * Select an AC drive of larger power class.
General| Model | MD280NT2.2GB |
|---|---|
| Type | Inverter |
| Rated Power | 2.2 kW |
| Output Current | 5.0 A |
| Frequency Range | 0 - 400 Hz |
| Communication Interface | RS485, Modbus |
| Cooling Method | Forced Air Cooling |
| Enclosure Rating | IP20 |
| Control Method | V/F control |
| Protection Features | Overvoltage, undervoltage, overcurrent, overload, short circuit |
| Ambient Temperature | -10°C to 50°C |
| Storage Temperature | -20°C to 60°C |
| Humidity | 5% to 95% (non-condensing) |
| Altitude | ≤1000 m |
| Input Voltage | 3-phase 380V AC |
Essential safety guidelines and warnings for installation, operation, and maintenance of the AC drive.
Important general precautions for handling, installation, and usage to ensure safe and reliable operation.
Details peripheral device selection, descriptions, wiring methods, and terminal layouts for electrical installation.
Describes the operation panel, including indicators, keys, and basic operations.
Details starting, stopping, JOG running, and different drive control modes.
Covers setting the running frequency using various sources like analog, pulse, and PID.
Provides a detailed list of faults, possible causes, and recommended solutions for the AC drive.
Summarizes common faults with initial analysis and troubleshooting steps.
To Next Page