Intermec PX4i

Appendix C — Fingerprint and IPL Setup Menus
172 PX4i and PX6i High Performance Printer User’s Manual
IPL Media Menu
IPL Configuration Menu
MEDIA TYPE:
CONTINUOUS
MEDIA TYPE:
MARK
SETUP:
MEDIA
MEDIA:
MEDIA TYPE
MEDIA TYPE:
GAP
MEDIA:
PAPER TYPE
PAPER TYPE:
TTR
PAPER TYPE:
DT
MEDIA:
LBL LENGTH DOTS
LBL LENGTH DOTS:
1200
MEDIA:
LBL REST POINT
LBL REST POINT:
0
MEDIA:
FORM ADJ DOTS X
FORM ADJ DOTS X:
0
MEDIA:
FORM ADJ DOTS Y
FORM ADJ DOTS Y:
0
100/200/400/800/
1200/1600/2000/
2500/3000/3600/
4200/4800
0/2/4/6/8/10/15/20/25/
30/-30/-25/-20/-15/-10/
-8/-6/-4/-2
0/2/4/6/8/10/15/20/25/
30/-30/-25/-20/-15/-10/
-8/-6/-4/-2
0/2/4/6/8/10/15/20/25/
30/-30/-25/-20/-15/-10/
-8/-6/-4/-2
MEDIA:
RIBBON LOW
RIBBON LOW:
0
0/5/10/15/20/25/30/35/
40/45/50/55/60/65/70/
75/80
MEDIA:
PAPER LOW
PAPER LOW:
0
0/10/20/30/40/50/60/70/
80/90/100/110/120/130/
140/150
MEDIA:
TESTFEED MODE
TESTFEED MODE:
FAST
MEDIA:
SENSITIVITY
SENSITIVITY:
420
MEDIA:
DARKNESS
DARKNESS:
0
120/130/140/160/170/
180/222/226/236/238/
366/369/420/440/450/
460/470/480/513/527/
533/563/565/567/623/
627/633/647/673/677/
687/720/854/864
0/1/2/3/4/5/6/7/8/
9/10/-10/-9/-8/-7/
-6/-5/-4/-3/-2/-1
EMULATION MODE:
86XX-15MIL
PRINT SPPED:
4 IN/SEC
PRINT SPPED:
3 IN/SEC
PRINT SPPED:
2 IN/SEC
PRINT SPPED:
8 IN/SEC
PRINT SPPED:
7 IN/SEC
PRINT SPPED:
6 IN/SEC
SETUP:
CONFIGURATION
CONFIGURATION:
LTS CALIBRATION
LTS CALIBRATION:
PRESS <ENTER>
REMOVE LABEL AND
PRESS ENTER
CONFIGURATION:
PWRUP EMULATION
CONFIG:
DISABLE
CONFIG:
ENABLE
CUTTER:
NOT INSTALLED
Labels are fed out
SENSITIVITY 9
OUT OF 8-14
Press E
Read only,
press E
CONFIGURATION:
PRINT SPEED
PRINT SPEED:
5 IN/SEC
CONFIGURATION:
CUTTER
PWRUP EMULATION:
EMULATION MODE
EMULATION MODE:
86XX-10MIL
EMULATION MODE:
5MIL
EMULATION MODE:
NONE
EMULATION MODE:
86XX-15MIL
PRINT SPPED:
4 IN/SEC
PRINT SPPED:
3 IN/SEC
PRINT SPPED:
2 IN/SEC
PRINT SPPED:
8 IN/SEC
PRINT SPPED:
7 IN/SEC
PRINT SPPED:
6 IN/SEC
SETUP:
CONFIGURATION
CONFIGURATION:
LTS CALIBRATION
LTS CALIBRATION:
PRESS <ENTER>
REMOVE LABEL AND
PRESS ENTER
CONFIGURATION:
PWRUP EMULATION
CONFIG:
DISABLE
CONFIG:
ENABLE
CUTTER:
NOT INSTALLED
Labels are fed out
SENSITIVITY 9
OUT OF 8-14
Press E
Read only,
press E
CONFIGURATION:
PRINT SPEED
PRINT SPEED:
5 IN/SEC
CONFIGURATION:
CUTTER
PWRUP EMULATION:
EMULATION MODE
EMULATION MODE:
86XX-10MIL
EMULATION MODE:
5MIL
EMULATION MODE:
NONE