Jacuzzi Flow User Manual

2121
XCheck that the spotlights switch on and o using the key .
XCheck that there are no leaks from the hydraulic connections
or other problems.
XCompletely disinfect the spa by carrying out “super-chlorin-
ation” treatment (it is also referred to as schock treatment, see
the user manual, chapter ”Water treatment”).
This operation is recommended when installing, or after a long pe-
riod of not using the spa.
XAfter a few hours, turn o the omnipolar switch.
XOpen the drain valve(s) and completely empty the spa.
XIf included, re-install the front and side panels.
CAUTION

Do not use the spa the rst time you start it as there is a
high concentration of chlorine in the water during this
phase. Immediately empty the bath.
Contact the local authorities for the standards govern-
ing the discharge of chemically treated water.
XClose the drain valve(s) and ll the spa again with fresh water
as previously explained.
XTurn the omnipolar switch back on and check that the spa
works correctly.
XCheck and as necessary modify the water ltering cycles
based on how you intend to use the spa.
QInstallation of Flow fronts
XReassemble the front panels (refer to the installation manual
for the front panels).
Control panel and functions
(4) All spa functions are managed by the control panel on the
tub, as are the respective settings/programming.
NOTE: the display is equipped with keys “ ” and “ ” to increase
or decrease the values.
QSetting the water temperature
The water is heated by a tubular electrical heater. Do not set an
excessively high water temperature, i.e. over the limit of 40 °C. The
recommended temperature is 35-36 °C.
NOTE: with the version with 1.5 Kw heater, when the pump is
activated, the heater is turned o (the LED relative to the symbol
ashes) and is turned on once again after the pump has been
switched o.
Water heating temperature (“set point”).
To check or modify the water heating temperature, do the following:
XPress keys “
” or “ ”: the display will show the current
memorized temperature.
XKeep keys “ ” or “ ” pressed down to change the value pre-
sented, from a minimum of 15 °C to a maximum of 40 °C
NOTE: press the “ ” key to increase the value or the “ ”key to
decrease it.
XTo show the temperature of the water in the tub again, do
not touch any key for about 5 seconds.
XAs soon as the water temperature set point is reached, the
heater is shut o. It will not be turned back on until the water
temperature drops about 0.5 °C below the set point.
XTo ensure precise measurement of the water temperature,
the ltering pump comes on every half hour for about 30 sec-
onds (even if no ltering cycles were set), since the temperature
probe is located in the heater pipe.
NOTES
When the system is turned o, or there is a power outage, the last
set point is stored in memory.
Operation of the heater is shown on the display by a LED on
steady under the symbol
.
CAUTION

Do not use the spa if the water temperature is 40 °C or more.
Maintenance of minimum temperature of water in tub and
anti-freeze protection of the pipes (“Smart Winter”).
At regular intervals, the system reads the actual temperature. If it
is below the minimum admissible value (14 °C), the heater and the
ltering pump are automatically activated until the temperature
rises above that value.
The pump is turned on, and turns o after 1 minute. During this
cycle the heater is turned o but will be reactivated later.
XThe pumps are turned on at preset intervals, depending on
the temperature:
- temperature between 12 and 14 ° C:
Every 2 hours
- temperature between 9 and 12 ° C:
every hour
- temperature between 6 and 9 ° C:
every 30 minutes
- temperatures at or below 6 ° C:
every 15 minutes
NOTES
- If it becomes necessary to turn on the anti-freeze protection dur-
ing the ltering cycles, those cycles will be suspended and they will
resume when the anti-freeze cycle is complete.

Jacuzzi Flow Specifications

General

Brand	Jacuzzi
Model	Flow
Category	Hot Tub
Language	English