<[~S£S:>
VM9313
SATELLITE
RADIO
OPERATION
Listeners can subscribe to
X~
Radio on the
Web
by
visiting www.xmradio.com.
or
by
calling
(800)
967-2346.
Customers
should
have theirRadio
10
ready (see
"Displaying the Identification
(10)
Code'? Customers can
receive
a limited number
of
free-to-air channels without
activation.
Accessing
Satellite
Radio
Mode
Press the
SRC
button (6) on the front panel
or
remote control
(8) to switch to the SAT source.
1.
SAT channel name
2. SAT channel number
3. SAT band
4. Time
5.
Song title
6. Artist
name
7. Song category
8. Signal Strength Indicator
9.
Current preset channels/on-screen preset buttons
10. CH
-:
Select the previous channel
11.
CH
+:
Select the next channel
12.
CAT
+:
Select next channel in current category
only
13. CAT
-:
Select previous channel in current category only
14. Touch to enter channel directly using keypad on screen
15.
CG: Access Channel/Category Guide mode
16.
BAND: Change between SAT1, SAT2 and SAT3 bands
17.
~:
Touch to view the SETUP menu
18. Touch this area to view the SOURCE MENU and select
a new playback source
19. MEM: View screen used to enter current channel into
preset memory
Displaying
the
Identification
(ID)
Code
Before you listen to satellite radio, you must subscribe to the
service using your radio's identification number.
To
display
the radio ID, press CH -
or
CH + buttons on the touch screen
repeatedly to tune to channel
'000'.
The screen displays the
radio ID where the channel name is usually displayed.
Selecting
a
Station
Press the 1«
or
»1
buttons (17, 19) on remote control
or
the
CH -
or
CH + buttons on the touch screen to change to
another station.
Preset
Mode
To
enter preset mode, touch the BAND button on the screen,
or
press the BAND button on the unit (3)
or
remote control
(30) to change between the following bands: SAT1, SAT2,
or
SAT3 (indicated in the top left
comer
of
the
TFT
screen).
Six numbered preset buttons store and recall stations for
each band. All six stored stations (P1-P6)
for
the current
band appear on the
TFT
screen.
Storing a Station
1. Select a band
(if
needed), then select a station.
2. Touch the on-screen
MEM
button (18) to open the
preset screen.
ICH###
I
~§J@J
P4§J~
[
Ex
i t
I
3. Touch the preset number in which you would like to
store the current station (or press
EXIT
to cancel and
close the menu). The preset number and station
appears highlighted.
Recalling a Station
1. Select a band
(if
needed).
15
2. Touch an on-screen preset button to select the
corresponding stored station.
Direct
Tuning
To
enter a radio station directly, touch the
88888
button
or
press the
GOTO
button (21) on the remote control to display
the direct entry menu.
ICH: /255 I
UJ00Q
GJ00D
0000
01
Clear
10
Enter the desired radio station using the on-screen'
number
pad. Press the enter button (arrow) to tune to the selected
station.
To
exit the screen without changing the station, touch
Exit.
To
clear
your
entry and start over, touch Clear.
Channel/Category
Guide
Mode
There are two search modes to help navigate through
channels and
or
categories.
To
access the Channel/Category
Guide mode press, the ZOOM button (23) on the remote
control
or
the CG button on the touch screen.
Channel Guide is the default search mode.
To
access
Category Guide, press the TITLE button (2) on the remote
control
or
touch CAT on the touch screen.
To
return to
Channel Guide, touch CH on the screen
or
press the
SUBTITLE
button (9) on the remote control.
Channel Guide Mode
When Channel Guide mode is selected, the first six satellite
channels are displayed in the boxes in the bottom left
of
the
TFT
screen and the on-screen menu changes to facilitate
search mode.
To Next Page
Loading...
