VM9313
<IE:
siD
----
,~-_.~
---~
~---
L.~~
~
-.!
1.
Touch the
ggggg
button to open the direct dial screen.
NOTE:
Not
all
phones
allow
access to missed, received
or
dialed calls
and
some
will
not
allow
uploading
of
your
phone'S address book.
Exit
32
1
2. Use the 0-9,
.,
and # buttons to input the phone number.
• Touch the
CLEAR
button to clear the last digit.
• Touch the
C'
button to clear the entire number and
start over.
3.
After entering the phone number, press the r button to
dial the call. The direct dial screen will close once your
call is connected.
To
end the conversation, press the t8 button.
Menu
List
The menu list appears on the left side
of
the screen and can
be accessed from other modes by touching the MENU button
on the right side
of
the screen.
i-~
i 5
-~
-6~,
'
CI~ar
;
~_.
__
~
'---
...-'
• 1
L..-
;
I
i----
----:
~-----I
..
------·--·--i
;---------:
.'
7
ii
8'
9
i'e-:
,
~
L.....----.J
I I I
* : 0 ,
i-it'
i--
~---;
i
_~~:
'
__
.....J-'::;====-.:===:.-'
Call
Transfer
While talking, to transfer audio from the head unit back to the
mobile phone, touch the
('J
button (6). The TFT will display
"Transfer".
You
can only transfer a call after it has been
answered.
Missed Calls
The Missed Calls list retrieves the list
of
Missed numbers
from your phone. The last missed number is the first number
on the list. Touch the Missed Calls menu option to view the
list.
To
make a call from the Missed Calls list, touch the
number and then touch the
......
button. The TFT will display
"Cannot get missed record" when the feature is not available.
NOTE: The TALK
button
on
the BTM10 can
be
used
to
answer
calls
or
hang up.
Each time the R button is pressed, the head unit will
automatically reconnect with the mobile phone once (only
if
the mobile phone was previously paired with the head unit).
Managing
Incoming
Calls
When connected to a Bluetooth phone, the unit will mute
audio output, pause CD play, and change to the Bluetooth
screen when a call is received.
An
incoming phone number
will appear at the top
of
the screen.
Answering
an
Incoming
Call
To
answer the call, touch the
~
button (11).
For best reception, speak loudly and clearly.
To
end the conversation, press the t8 button (12). The
screen will display the call duration for 3 seconds, and then
retum to the previous mode.
Rejecting
an
Incoming
Call
Touch the t8 button to reject
an
incoming call. The call will
revert to your phone and can be answered directly or left for
voice mail.
Volume
Control
To
increase
or
decrease the volume level, tum the AUDIO
control (5) on the front panel
or
press the VOL+I
VOL-
buttons on the remote control (15, 16).
Microphone Mute
To
mute the microphone, touch the
~
button (10). Touch
again to resume microphone functionality.
NOTE: Press the
~
button
from the main Bluetooth
screen to
automatically
dial
the
last
call
received,
Making
an
Outgoing
Call
1.
Press the ((* button (7) to initiate the pairing process.
Keep the mobile phone within 2 meters
of
the head unit
when pairing.
(To
terminate the pairing process, press
the
U*
button again.)
2. Select the Bluetooth setup option on the mobile phone
to be paired (please refer to the phone's instruction
manual to learn how to enter Bluetooth setup, tum
Bluetooth on/off, and perform pairing).
the telephone source. However, depending on your phone,
the connection may be made using HSP (Head Set Profile),
making some functions unavailable. This is a limitation
of
your phone, not the VM9313.
Since there are a number
of
Bluetooth mobile phone
implementations available
on
the market, operations with
your Bluetooth mobile phone using this unit vary greatly.
Please refer to the instruction manual that came with your
Bluetooth mobile phone along with this manual while
operating your phone with this unit.
Pairing
the
Bluetooth
System
with
Your
Mobile
Phone
and
Head
Unit
NOTE: Some phones require a "pass
key"
or
pairing
code
to
connect.
"your
phone requires a
pass
key
or
pairing
code,
you
will
need to
enter
this
number
In the
Pairing Code field
under
the Bluetooth SETUP menu. The
default
pairing
code
for
many
phones
Is "0000",
The
default code
for
the VM9313Is "1234", See "Bluetooth
Sub-menu Features" on page
11
for
Instructions
on
entering the
pairing
code.
3. Select "VM9313" from the pairing list on the mobile
phone.
• Ifpairing is successful, the TFT will display the paired
mobile phone model number
or
name (as specified
in
your phone's Bluetooth Setup menu).
• Ifpairing fails, "Phone Pairing Fail" is displayed at the
bottom
of
the screen.
Reconnecting
Once the Bluetooth device has been paired, you can touch
the connect R button (9) to reconnect.
NOTE: You can
only
connect
to a
phone
using
the
buttons
on
the on-screen Phone interface,
26
To Next Page
Loading...
