Available Surround modes vary depending on the incoming signals.
Activating one of the Surround modes for a source automatically
recalls the memorized settings and adjustments (see pages 16 to
22).
m Auto Surround Function
This receiver has Auto Surround Function, which allows you to
enjoy the Surround mode simply by selecting the source (with
digital input selected tk)rthat source),
Auto Surround works...
• When multi-channel signal is detected, an appropriate Surround
mode will be turned on.
• When Dolby Digital 2-channel with surround signals is detected,
"PLII MOVIE" will be selected.
• When Dolby Digital 2-channel without surround signals or Linear
PCM signal is detected, "SURROUND OFF" will be selected.
Note:
This function does not take effect in the following cases:
- While playing an analog source,
- While selecting any of DSP modes (see page 26), and
- While listening with the headphones--"HEADPHONE" or
"3D H PHONE" (see pages 11 and 24).
m Activating the Surround Modes ManuaRv
JVC O
I I :
[ I
== o©o
Select and play any source.
" Make sure you have selected the analog or digital input mode
correctly.
Press SURROUND to activate the Surround
mode.
• When "DOLBY DIGITAL," "DTS SURROUND," or "DUAL
MONO" is selected as the Surround mode, pressing
SURROUND changes the indication on the display alternately
between "AUTO SURROUND" and each Surround mode.
(The surround effect does not change.)
• For Dolby Digital multi-channel digital software (except
2-channel and Dual Mono software), incoming signals are
automatically detected and "DOLBY DIGITAL" is activated.
DIGITA"AUTOINITN
l'Eg_ u:E
I][1 DIGITAL I_ I [] T-! '" "=""" ''
LJi ...... j[i 'i'
AJ
"T]"T..... T" .'r r'-'i
.!J.±.i.2:i.i.i i11 .....
• For DTS multi-channel digital software (except 2-channd
and Dual Mono software), incoming signals are
automatically detected and "DTS SURROUND" is activated.
DIGITALAUtONINE]
LFE .=...
[] [] ii"- .....i ",
f- t i f-'i f-'i f"'i i i i', i TI
....ii ii"f i"Vi ii ii,,i J_
.............................. I11
Note:
When the Dolby Digital or DTS multi-channel digital signal stops
coming in, "PLII MOVIE" will be activated.
• For analog sources and digital 2-channel software, you can
select one of the following Surround modes. Each time you
press SURROUND, Surround modes change as follows:
ANAL_
INE]E]
[g[[ PRO LOGIC If
PLII MOVIE , PLII MUSIC
(Dolby Pro Logic II Movie) (Dolby Pro Logic II Music)/
AUTO SURROUND*+---- PLII GAME
(Dolby Pro Logic II Game)
* The receiver automatically changes the Surround mode to "PLII
MOVIE" o1""SURROUND OFF" according to the input signal.
• For Dual Mono software, you can select the channel you
listen to. (See page 19.)
DUALMONO
DIGITAL AUTO L E]
O0 DIGITAL
TII I'i-II ""'--'"' '-'
............... ! ! !._! ! ! !._!
To adjust the speaker output level, center tone, and sound effect
of Dolby Pro Logic II Music, see page 22.
To cancel the Surround mode
Press SURROUND/DSP OFF.
DIGITAL AUTO IN C E]
[_ LFE
I:11:]DIGITAL i'--" i'--'i i'--'i f--ii ii <,i .... f--i [[ r'[
...."il ii"_:i"::i ii ii',i II .... , ,
When playing Dolby Digital Surround EX or DTS-ES software
You can enjoy Virtual 6.1-channel playback using Virtual
Surround Back.
To activate Virtual Surround Back, see page 20.
VIRTUAL GB
DIGITAL AUTO INrc_lE]
[] [] ,!',-,!"_ i ,::i 1-1,,1
s_ . i..... ! _i'll i_i i !
25
To Next Page
Loading...
Need help?
General
