Why is the LUX light not on in my KaVo ELECTROmatic PM Dental equipment?
The LUX light might not be on because the LED is defective. Replace the LED. Also, the motor hose could be defective, so replace the motor hose. Finally, the device itself could be defective, so replace the control unit. If error persists, notify the service engineer.
What to do if my KaVo Dental equipment malfunctions (no display, the LED on the rear of the device flashes)?
If your device malfunctions with no display but the LED on the rear flashes, it could be due to no voltage supply on the control panel or no connection to the control panel. Check and restore the correct connection. Try replacing the connection cord to the control panel or replacing the control panel itself. If error persists, notify the service engineer.
What to do if my KaVo ELECTROmatic PM Dental equipment malfunctions (no display, the LED on the rear of the device does not flash)?
If your device malfunctions with no display and the LED on the rear doesn't flash, the cause might be no voltage supply. Check and restore the correct voltage supply and connection. Check that the standby LED on the power supply is on. If the standby LED on the power supply is not on, replace the power supply. If error persists, notify the service engineer.
Why is there no or insufficient spray water in my KaVo ELECTROmatic PM?
There could be several reasons for insufficient spray water. The spray water regulation might be closed, so open it as much as possible. The water line could be soiled; in this case, pull off the handpiece and actuate the spray water in bursts to rinse it. Another cause may be that the filter insert is soiled, so replace the filter on the water inlet. Finally, the spray water on the treatment center or foot control could be closed, so open the spray on the treatment center. If the error persists, unscrew the turbine hose and check if any water flows. If no water flows, notify a service engineer.
What to do if SAFEdrive icon flashes yellow on my KaVo Dental equipment?
If the SAFEdrive icon is flashing yellow, it means the motor is overloaded. If you are using a handpiece from a third-party manufacturer, deactivate SAFEdrive or use a high-speed handpiece from KaVo. If you are using a KaVo high-speed handpiece, relieve the handpiece of its load for at least 2 seconds by lifting it off the tooth. Once the motor reaches maximum speed again and the SAFEdrive icon turns yellow, continue working as usual, making sure to use intermittent mode as the operating mode.
What to do if SAFEdrive icon flashes red on my KaVo ELECTROmatic PM?
If the SAFEdrive icon flashes red and the motor stops automatically, it indicates the motor is overloaded. If you're using a third-party handpiece, try deactivating SAFEdrive or switch to a KaVo high-speed handpiece. If you're already using a KaVo high-speed handpiece, take it out of the patient's mouth and inspect the handpiece head for temperature, damage, and ease of operation. If there's no damage or overheating, restart the motor by pressing the foot control again. Service the handpiece. However, if you notice damage or overheating, replace the handpiece or have it repaired.
What does Event E2 mean on KaVo Medical Equipment?
Event E2 on your KaVo Medical Equipment indicates that the foot control is being pressed during start-up. Avoid pressing the foot control when switching the unit on.
What does Event E3 mean on KaVo Medical Equipment?
Event E3 on your KaVo Medical Equipment means that no motor is connected. Connect the motor.
What does Event E4 mean on KaVo Medical Equipment?
Event E4 on your KaVo Medical Equipment indicates that the motor is blocked. To resolve this, relieve the motor of its load, then stop and start it using the foot control.
What does Event E5 mean on KaVo Medical Equipment?
Event E5 on your KaVo Medical Equipment indicates automatic light and motor shut-off during continuous operation of the motor. Comply with the defined operating mode.
General overview and essential information for safe and correct operation of the device.
Identifies risks of infection from contaminated devices and outlines necessary precautions.
Warns about risks of explosion or fire due to electrical sparks in specific environments.
Emphasizes maintaining the product in good technical condition to prevent injury.
Details risks of electrical shock and injury from liquid ingress and how to prevent it.
Safety guidelines for using approved accessories and avoiding unauthorized modifications.
Stresses the need for trained personnel and proper understanding of instructions for safe operation.
Outlines who is authorized for service/repair and the procedures required for safety checks.
Defines the product's purpose, indications, and proper usage for dental treatments.
Provides detailed technical data including dimensions, weight, ambient conditions, and electrical ratings.
Outlines various methods and positions for physically mounting the ELECTROmatic unit.
Instructions on how to start the motor using the foot control and achieve desired speeds.
Explains how to adjust the spray water volume for cooling and lubrication.
Describes how to change and save motor speed presets using the control panel or foot control.
Details the SAFEdrive function for detecting and preventing overheating of handpieces.
Guidelines for cleaning the device, including preparation, external, and internal cleaning procedures.
Instructions for disinfecting the device surfaces using approved methods and products.
General| Supply voltage | 100-240 V |
|---|---|
| Frequency | 50/60 Hz |
| Power | 60 W |
| Type | Electric motor |
| Voltage | 24 V |
| Handpiece Connection | ISO 3964 |
To Next Page