Keysight PNA-X Series Configuration Guide

Page 39
Find us at www.keysight.com
For devices with 1.85 mm connectors (Continued)
Electronic calibration kits
N4694A Microwave ECal: 10 MHz to 67 GHz, 2-ports. Includes:
– Option M0F module with: N4694-60001 1.85 mm (f) to
1.85 mm (m) ECal module
– Option 00M module with: N4694-60002 1.85 mm (m) to
1.85 mm (m) ECal module
– Option 00F module with: N4694-60003 1.85 mm (f) to
1.85 mm (f) ECal module
– Option 00A adds:
– 85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
– 85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
– Option 150: Replaces standard storage container with a
wooden box
N4694D
1
Microwave ECal: DC or 10 MHz to 67 GHz, 2-ports.
Includes:
– Option F0F: Both connectors are 1.85 mm female on module
– Option M0F: 1 female and 1 male 1.85 mm connector on
module
– Option M0M: Both connectors are 1.85 mm male on module
– Option 0DC: DC to 67 GHz
– Option 100: 10 MHz to 67 GHz
– Option 00A adds:
– 85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
– 85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
Cables
– N4697E
2
Single, flexible:
– 1.85 mm (f) to 1.85 mm (f), 96.5 cm, 38 inches
– N4697F
2
Set, flexible:
– One 1.85 mm (f) to 1.85 mm (f) cable, 62.2 cm,
24.5 inches, p/n N4697-60100
– One 1.85 mm (f) to 1.85 mm (m) cable, 62.2 cm,
24.5 inches, p/n N4697-60200
– N4421B-K67 Single, flexible: 1.85 mm (f) to 1.85 mm (m),
91.4 cm, 36 inches
Adapter set
– 85130H
2
1.85 mm to 1.85 mm
For devices with 2.4 mm connectors
Mechanical calibration kit
85056A standard: DC to 50 GHz. Includes:
– 00901-60003 2.4 mm (m) fixed broadband load
– 00902-60004 2.4 mm (f) fixed broadband load
– 00915-60003 2.4 mm (m) sliding load
– 00915-60004 2.4 mm (f) sliding load
– 85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
– 85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
– 85056-60007 2.4 mm (m) to 2.4 mm (f) adapter
– 85056-60020 2.4 mm (m) short
– 85056-60021 2.4 mm (f) short
– 85056-60022 2.4 mm (m) open
– 85056-60023 2.4 mm (f) open
– 85056D economy: DC to 50 GHz. Includes:
– 00901-60003 2.4 mm (m) fixed broadband load
– 00902-60004 2.4 mm (f) fixed broadband load
– 85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
– 85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
– 85056-60007 2.4 mm (m) to 2.4 mm (f) adapter
– 85056-60020 2.4 mm (m) short
– 85056-60021 2.4 mm (f) short
– 85056-60022 2.4 mm (m) open
– 85056-60023 2.4 mm (f) open
Electronic calibration kits
N4693A Microwave ECal: 10 MHz to 50 GHz, 2-ports. Includes:
– Option M0F module with: N4693-60001 2.4 mm (f) to
2.4 mm (m) ECal module
– Option 00M module with: N4693-60002 2.4 mm (m) to
2.4 mm (m) ECal module
– Option 00F module with: N4693-60003 2.4 mm (f) to
2.4 mm (f) ECal module
– Option 00A adds:
– 85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
– 85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
– Option 150: Replaces standard storage container with a
wooden box
N4693D
1
Microwave ECal: DC or 10 MHz to 50 GHz, 2-ports.
Includes:
– Option F0F: Both connectors are 2.4 mm female on module
– Option M0F: 1 female and 1 male 2.4 mm connector on
module
– Option M0M: Both connectors are 2.4 mm male on module
– Option 0DC: DC to 50 GHz
– Option 100: 10 MHz to 50 GHz
– Option 00A adds:
– 85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
– 85058-60006 2.4 mm (f) to 2.4 mm (f) adapter
1. The PNA Series must have firmware revision A.12.85.00 or above for
operation with the N469xD Series ECal.
2. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard male
connector.

Keysight PNA-X Series Specifications

General

Output Power	+13 dBm (typical)
Number of Ports	2 or 4
Dimensions	426 mm (W) x 470 mm (D)
Power Requirements	100 to 240 VAC, 50/60 Hz
Frequency Range	10 MHz to 26.5 GHz (varies by model)