Keysight PNA-X Series Configuration Guide

Page 41
Find us at www.keysight.com
Mechanical calibration kits, continued
Electronic calibration kits
N4692A Microwave ECal: 10 MHz to 40 GHz, 2-ports. Includes:
– Option M0F module with: N4692-60001 2.92 mm (f)
to 2.92 mm (m) ECal module
– Option 00M module with: N4692-60002 2.92 mm (m) to
2.92 mm (m) ECal module
– Option 00F module with: N4692-60003 2.92 mm (f) to
2.92 mm (f) ECal module
– Option 00A adds:
– N4692-60021 2.92 mm (m) to 2.92 mm (m) adapter
– N4692-60022 2.92 mm (f) to 2.92 mm (f) adapter
– Option 150: Replaces standard storage container with a
wooden box
N4692D
1
Microwave ECal: DC or 10 MHz to 40 GHz, 2-ports.
Includes:
– Option F0F: Both connectors are 2.92 mm female on module
– Option M0F: 1 female and 1 male 2.92 mm connector on
module
– Option M0M: Both connectors are 2.92 mm male on module
– Option 0DC: DC to 40 GHz
– Option 100: 10 MHz to 40 GHz
– Option 00A adds:
– N4692-60021 2.92 mm (m) to 2.92 mm (m) adapter
– N4692-60022 2.92 mm (f) to 2.92 mm (f) adapter
Cables
Note: Keysight offers the following 2.4 mm test port cables.
Adapters will be necessary when using these cables for 2.92 mm
measurements.
– 85133C
2
single, semi-rigid: 2.4 mm (f) to PSC-2.4 mm (f),
81 cm, 32 inches
– 85133D
2
set, semi-rigid:
– One 2.4 mm (f) to 2.4 mm (m), 53 cm, 21 inches, p/n
85133-60001
– One 2.4 mm (f) to 2.4 mm (f), 53 cm, 21 inches, p/n
85133-60002
– 85133E
2
single, flexible: 2.4 mm (f) to PSC-2.4 mm (f), 97 cm,
38 inches
– 85133F
2
set, flexible:
– One 2.4 mm (f) to 2.4 mm (f), 63 cm, 25 inches,
p/n 85133-60016
– One 2.4 mm (f) to 2.4 mm (m), 63 cm, 25 inches,
p/n 85133-60017
– 85133H
2
Single, flexible: 2.4 mm (f) to 2.4 mm (m), 63 cm,
25 inches
– N4421AK20 Single, flexible: 2.4 mm (f) to 2.4 mm (m),
91.4 cm, 36 inches
Adapters
– 11904A 2.4 mm (m) to 2.92 mm (m)
– 11904B 2.4 mm (f) to 2.92 mm (f)
– 11904C 2.4 mm (m) to 2.92 mm (f)
– 11904D 2.4 mm (f) to 2.92 mm (m)
– 11904S 2.4 mm to 2.92 mm
– Adapter set, contains 4 matched adapters
For devices with K connectors (2.92 mm) (Continued)
1. The PNA Series must have firmware revision A.12.85.00 or above for the
operation with the N469xD Series ECal.
2. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard male
connector.

Keysight PNA-X Series Specifications

General

Output Power	+13 dBm (typical)
Number of Ports	2 or 4
Dimensions	426 mm (W) x 470 mm (D)
Power Requirements	100 to 240 VAC, 50/60 Hz
Frequency Range	10 MHz to 26.5 GHz (varies by model)