Krone Comprima V 180 XC - Insert Net

Operation
163
Pos: 48.99.15 / BA/Bedienung /R undballenpresse/N etzbindung _nur Ausführung N etzbindung a b 17 18/Netz-/F olienrolle einlegen_Bild2 @ 507\mod_ 1500291585475_7 8.docx @ 348 4634 @ @ 1
COM00595
12
Fig.
134
Pos: 48.99.16 / BA/Bedienung /R undballenpresse/N etz- un d Folienbindung_A usführung N etz- und Folien bindung ab 17 18 /Netz-/Folie nrolle einlegen_T ext2 @ 513\m od_15036472 91466_78.doc x @ 3532609 @ @ 1
If the net or film roll (9) has not been centrally aligned:
• Loosen the two adjusting rings (8, 11).
• Use a mounting lever (12) to push the net or film roll (9) in the desired direction shown by
the arrow until the net or film roll (9) is positioned in the centre.
• Push the two adjusting rings (8, 11) with a distance dimension each of 2-3 mm towards the
inner cardboard tube (10) and fix them in this position.
Pos: 48.99.17 /Ü berschriften/Ü berschriften 3/K- O/N/Netz einleg en @ 74\ mod_1308810058 091_78.doc x @ 657911 @ 3 @ 1
11.19.3 Insert Net
Pos: 48.99.18 / BA/Sicherheit/ 7. Gefahrenhinw eise alt/Rundballe npresse/Warn ung Messer N etz einlegen CF/CV @ 308\ mod_1416899 786255_78.docx @ 2390286 @ @ 1
WARNING! - Risk of Cuts Due to Sharp Cutters!
Serious injuries; especially to hands.
• Wear protective gloves when working in the area of the blades and the blade bar
• Wear also protective gloves when threading in or removing the net
Pos: 48.99.19 / BA/Bedienung /R undballenpres se/Netzbindu ng_nur Ausführ ung Netzbindung ab 17 18/Hi nweis_KRONE Ne tz verwenden @ 513\mod_ 1503325136071_ 78.docx @ 3 528536 @ @ 1
Note
For trouble-free use in the field, KRONE recommends one of the "KRONE excellent" nets, see
label at the machine with the number 27 018 640 *.
Pos: 48.99.20 / BA/Bedienung /R undballenpresse/N etz- un d Folienbindung_A usführung N etz- und Folien bindung ab 17 18 /Terminal Netzbi ndung ausge wählt_Vorauss etzung @ 513\ mod_150364 9652260_78.doc x @ 3532692 @ @ 1
Prerequisite
– Net wrapping has been selected, see chapter Terminal – Menus, Menu 8 "Tying type
selection".
Pos: 48.99.21 / BA/Bedienung /R undballenpresse/ Folienbind ung/Netz- oder F olienrolle einl egen_Netzschwi nge nach vorn fahren_bild N etzbindung_alle Co mprima @ 507\ mod_150 0357931883_78.d ocx @ 3485 458 @ @ 1
COM00488
3
2
1
Fig.
135
Pos: 48.99.22 / BA/Bedienung /R undballenpresse/ Folienbind ung/Folie/Netz einl egen_Netzs chwinge nach vorn fahren_text _alle Compri ma @ 513\ mod_150305473659 6_78.docx @ 3 509463 @ @ 1
• Move the feed rocker arm (3) with the terminal forward until the distance dimension
between the pressure axis covered in red foam wadding (2) and the deflection roll (1) is
approximately 5 cm, see chapter Terminal – Menus, "Menu 10, 'Manual operation'".
Pos: 48.99.23 / Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196 175311226_0. docx @ 4165 @ @ 1