Krone Comprima V 180 XC - Setting the Brake Force Release During the Feeding Process

Settings
182
Pos: 50.5.1 /Übersc hriften/Übersc hriften 2/A-E /BBremskrafte ntlastung beim Zu führen einst ellen @ 512\ mod_1502892696 010_78.doc x @ 3508735 @ 3 @ 1
12.1 Setting the brake force release during the feeding process
Pos: 50.5.2 /BA/ Einstellungen/Ru ndballenpress e/Netz- und Foli enbindung Eins tellungen/Br emskraftentlastu ng beim Zuführ en einstellen _bild_Netzbind ung_Netz- un d Folienbindung_ alle Comprim a @ 513\mod_ 1503474429854 _78.docx @ 35 29886 @ @ 1
COM00489
1
3
2
4
Fig.
153
Pos: 50.5.3 /BA/ Einstellungen/Ru ndballenpress e/Netz- und Foli enbindung Eins tellungen/Br emskraftentlastu ng beim Zuführ en einstellen _einl_Netzbind ung_Netz- un d Folienbindung_ alle Comprim a @ 513\mod_ 1503475326578 _78.docx @ 35 29917 @ @ 1
In particular in the chamber film wrapping version, there is the risk that the film will overturn at
the film roll instead of being fed to the round bale. If this happens, the brake force release
during the feeding process should be adjusted.
While the wrapping material is guided to the round bale, the brake force should be reduced so
that the wrapping material can be pulled off more easily from the round bale.
This brake force release during the feeding process can be set at the spring (3) at the right
machine side behind the side hood.
The more the spring (3) is tensioned, the greater the brake force release during the feeding
process.
Pos: 50.5.4 /Übersc hriften/Zwisc henüberschriften/U- Z/Vora ussetzung @ 4 63\mod_146657 2209300_78.doc x @ 3123726 @ @ 1
Prerequisite
Pos: 50.5.5 /BA/ Einstellungen/Ru ndballenpress e/Netz- und Foli enbindung Eins tellungen/Zu führschwinge b efindet sich in Zu führposition, si ehe Kapitel_V oraussetzung @ 514\mod_ 1503655894602_ 78.docx @ 3 532819 @ @ 1
– The feed rocker arm is in feed position, see chapter Terminal, "Menu 10 'Manual
operation'".
Pos: 50.5.6 /BA/ Sicherheit/8. Vora ussetzungen/H andlungsanw eisung für alle M aschinen/Vor aussetzung: Die M aschine ist stillg esetzt und gesichert_ohn e Zwischenüb erschrift Vorauss etzung @ 514 \mod_1504092 581843_78.do cx @ 35346 68 @ @ 1
– Shut down and safeguard the machine, see chapter Safety, "Shutting down and
safeguarding the machine".
Pos: 50.5.7 /La yout Module /----------------Leerzeile-------------------- @ 240\mod_139 5147357027_ 0.docx @ 1890 988 @ @ 1
Pos: 50.5.8 /BA/ Einstellungen/Ru ndballenpress e/Netz- und Foli enbindung Eins tellungen/Br emskraftentlastu ng beim Zuführ en einstellen _text_Netzbindu ng_Netz- u nd Folienbindung_alle Compri ma @ 513\mod_1 50347584545 4_78.docx @ 3 529948 @ @ 1
• Check that the disc (2) is located above the spring (3) at the level of the central notch (4).
• To change the tension of the spring (3), loosen or tighten the nut (1).
Notches (4)
Spring tension (3)
Wrapping material during the feed
process
top
low
Pulling the wrapping material requires
much strength.
centre
medium
Pulling the wrapping material requires
medium strength. KRONE recommend
this setting as an optimum brake force
release during the wrapping material
feeding process.
bottom
high
Pulling the wrapping material requires
little strength.
Pos: 50.5.9 /La yout Module /---------------Seitenumbruch---------------- @ 0\mod_119617 5311226_0.doc x @ 4165 @ @ 1