Krone EasyCut 2801 CV - Oil Level Check and Oil Change on the Cutter Bar; Oil Change; Checking the Oil Level; Aligning the Cutter Bar

Maintenance
70
Pos: 26.34.1 /Üb erschriften/Üb erschriften 2/K-O/ Ölstandskontroll e und Öl wechsel am Mähhol m @ 0\mod_11 97017549815_ 78.docx @ 159 63 @ @ 1
10.10 Oil level check and oil change on the cutter bar
Pos: 26.34.2 /Üb erschriften/Üb erschriften 3/K-O/ Ölwechsel @ 0 \mod_1197021 941955_78.doc x@ 16139 @ @ 1
10.10.1 Oil change
Pos: 26.34.3 /B A/Wartung/Mäh werke/Hinweis Ei n Ölwechsel amM ähholm ist nicht erforderl ich. @ 68\mod _130457739138 8_78.docx @ 62 8708 @ @ 1
Note
No oil change is required on the cutter bar.
Pos: 26.34.4 /Üb erschriften/Üb erschriften 3/K-O/ Ölkontrolle @ 0\mod_11970 21908190_78.d ocx @ 16120 @ @ 1
10.10.2 Checking the oil level
Pos: 26.34.5 /B A/Sicherheit/Gefa hrenhinweise/Mä hwerke/Gef ahr- Schnell rotier ende Messerteller /Gefahr - Sc hnell rotierend eM essertell er/Messertrom mel_2 @ 0\mod_11 97022569252_ 78.docx @ 1 6165 @ @ 1
Danger! - Rapidly rotating cutting discs/blade drums.
Effect: Danger to life or serious injuries.
Lower guards. Nobody should be in the danger zone around the machine.
Pos: 26.34.6 /B A/Sicherheit/Gefa hrenhinweise/Mä hwerke/Gef ahr- Schnell rotier ende Messerteller /Gefahr - Sc hnell rotierend eM essertell er/Messertrom meln_1 @ 0\mod_1 197017696736 _78.docx @ 16001 @ 23 @ 1
Danger! - Rapidly rotating cutting discs/blade drums.
Effect: Danger to life or serious injuries.
• Switch off the engine and remove the ignition key.
• The cutting discs/blade drums continue to run!
• Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete
stop.
Pos: 26.34.7 /Üb erschriften/Üb erschriften 3/K-O/M ähholm ausric hten @ 0\mo d_119701795 6815_78.docx @ 1 6042 @ @ 1
10.10.3 Aligning the Cutter Bar
Pos: 26.34.8 /B A/Wartung/Mäh werke/Mähhol m ausrichten Eas yCut @ 3\mo d_1204721803648 _78.docx @ 7 2358 @ 3 @ 1
EC-0-001
Fig. 41
Oil level check
• Align the cutter bar using a spirit level (1).
Crosswise
• Lay the spirit level on top of the cutting disc hub parallel to the direction of travel.
Lengthwise
• Lay the spirit level (1) on top of two mower discs.
Pos: 26.34.9 /B A/-------- -------Seitenumbruch--- --------- ---- @0\ mod_11961753 11226_0.docx @ 4165 @ @ 1