Why can't I fit the BeerTender Keg tap in the tapping unit of my Krups Kitchen Appliances?
If you cannot fit the BeerTender Keg tap in the tapping unit, the BeerTender Keg tap may have been activated by hand. Put the BeerTender Keg tap back in its original position.
How to fix beer flowing out too slowly from Krups BeerTender Kitchen Appliances?
If beer is flowing out too slowly from your Krups Kitchen Appliances, make sure that the tap handle is opened completely.
Why I can not fit the BeerTender Keg tap in the tapping unit of Krups Kitchen Appliances?
If you cannot fit the BeerTender Keg tap in the tapping unit of your Krups Kitchen Appliances, it may be because the BeerTender Keg tap has been activated by hand. Put the BeerTender Keg tap back in its original position.
What to do if I can't close the tap cover of Krups Kitchen Appliances?
If you cannot close the tap cover on your Krups Kitchen Appliances, it's likely that the BeerTender Keg tap is not inserted correctly. Remove the BeerTender Keg tap from the appliance and fit it again.
Why Krups BeerTender does not turn on?
If your Krups Kitchen Appliances does not turn on, the appliance is not connected to the mains power supply. Connect the appliance to the power supply.
What to do if Krups BeerTender temperature indicator never reaches ready-to-drink level?
If the temperature indicator on the control display of your Krups Kitchen Appliances never reaches a ready-to-drink level, it may be because the appliance is exposed to a temperature that is too hot or to direct sunlight. Use the appliance indoors and move it to a room where the ambient temperature does not exceed 30°C.
How to fix increasing temperature on Krups BeerTender control display?
If the control display on your Krups Kitchen Appliances shows an increasing temperature, it could be because a warm keg was installed in a cold appliance. Allow the BeerTender system to compensate for the temperature change. The displayed temperature should start decreasing after a maximum of one hour.
What to do if no beer is being dispensed from Krups Kitchen Appliances BeerTender?
If no beer is being dispensed from your Krups BeerTender, there might be several reasons: * The BeerTender Keg could be empty. If the last level of the volume indicator is blinking, replace the BeerTender Keg with a new one. * There might be no keg inside the appliance. If the 4 levels of the volume indicator are blinking, install a keg inside the BeerTender appliance. * The tap handle might not be correctly installed or positioned. Ensure the tap is correctly installed and positioned.
Why is my Krups Kitchen Appliances BeerTender dispensing warm beer?
Your Krups BeerTender might be dispensing warm beer because the keg hasn't been chilled long enough in the refrigerator to reach the correct serving temperature. Allow the BeerTender Keg to cool in the refrigerator for about 12 hours. Alternatively, the beer may have been tapped before reaching the correct drinking temperature. In this case, allow the BeerTender Keg to cool long enough in the appliance.
Why does my Krups Kitchen Appliances BeerTender produce too much foam?
Excessive foam when dispensing beer from your Krups BeerTender can occur for several reasons: * The keg may not be cold enough. Allow the keg to cool until the temperature indicator shows it's ready. * The keg might have been shaken. If so, wait approximately 4 hours before dispensing. * You might be pulling the tap handle too slowly. Pull the handle down and forward firmly and quickly.
Instructions for user safety and proper use.
Advice on keeping instructions and seeking help.
Specifies the appliance's purpose and domestic setting.
Key factors for optimal draft beer quality and hygiene.
Methods and duration for chilling the beer keg before use.
Guidance on unpacking and placing the appliance.
Safety precautions and procedure for plugging in the appliance.
Step-by-step instructions for placing a beer keg inside.
Explanation of the appliance's display indicators.
Details on the sounds the appliance makes during operation.
How to prepare a glass for perfect draft beer.
Technique for pouring beer and avoiding excessive foam.
Letting the beer settle in the glass.
Characteristics of an excellent draft beer.
How to clean the drip tray and grate after each use.
Regular cleaning of the cooling chamber and tap cover.
General| Type | Beer Dispenser |
|---|---|
| Cooling System | Thermoelectric |
| Capacity | 5 Liters |
| Brand | Krups |
| Model | BeerTender |
| Category | Kitchen Appliances |
| Voltage | 120 V |
| Frequency | 60 Hz |
| Color | Black, Silver |
| Compatible Kegs | Heineken, Newcastle Brown Ale |
| Weight | 13.2 pounds |
| Temperature Indicator | LED |
| Compatibility | 5L Heineken DraughtKeg, 5L BeerTender Kegs |
| Material | Plastic |
To Next Page
