What to do if my KTM 200 EXC Motorcycle emits white smoke?
If you observe white smoke emission (steam in exhaust gas) from your KTM Motorcycle, it could be due to a damaged cylinder head or cylinder head gasket. Inspect the cylinder head and cylinder head gasket.
Why is gear oil coming out of the vent hose on my KTM Motorcycle?
If gear oil exits at the vent hose of your KTM Motorcycle, it's likely because too much gear oil was added. Check the gear oil level.
How to troubleshoot water in the gear oil of my KTM 200 EXC?
If there's water in the gear oil of your KTM Motorcycle, a damaged shaft seal ring or water pump could be the cause. Check the shaft seal ring and water pump.
What to do if KTM 200 EXC Motorcycle engine turns but does not start?
If your KTM Motorcycle engine turns over but doesn't start, consider these potential causes: an operating error during the start procedure; old fuel in the float chamber from prolonged disuse, requiring you to empty the carburetor float chamber; interrupted fuel feed, so check the fuel tank breather and clean the fuel tap, and check/set the carburetor components. Also, inspect a spark plug (if it's oily or wet, then clean and dry it, or replace it if necessary). Check the electrode distance (plug gap) of spark plug (adjust the plug gap to 0.60 mm (0.0236 in) for All 125/200/250/300 models). A fault in the ignition system or a defective kill switch could also be the reason, so check the ignition system and the kill switch. Finally, clean the connector and treat it with contact spray if the ...
Explains the meaning of specific symbols used in the manual.
Explains the typographical formats used in the document.
Defines the intended use for EXC and XC-W models.
General safety instructions for operating the vehicle.
Explains different degrees of risk and their associated symbols.
Warns against tampering with the noise control system.
Provides guidelines for safe operation of the motorcycle.
Emphasizes the importance of wearing protective clothing.
Outlines rules for performing work on the vehicle.
Discusses responsible use and environmental considerations.
Highlights the importance of reading and keeping the owner's manual.
Details conditions for guarantee and warranty claims.
Information on fuel, lubricants, and environmental hazards.
Advises on using approved spare parts and accessories.
Emphasizes the importance of proper service and maintenance.
Notes that figures may show special equipment or be simplified.
Information on contacting authorized KTM dealers.
Illustrates the front-left view of the motorcycle with numbered parts.
Illustrates the rear-right view of the motorcycle with numbered parts.
Shows the location of the chassis number.
Shows the location of the type label.
Shows the location of the key number.
Shows the location of the engine number.
Shows the location of the fork part number.
Shows the location of the shock absorber part number.
Describes the clutch lever for different models.
Identifies the hand brake lever and its function.
Identifies the throttle grip.
Explains the kill switch function and states.
Explains the kill switch function and states for XC-W.
Identifies the horn button and its operation.
Explains the light switch functions.
Explains the light switch functions for XC-W.
Explains the turn signal switch operation.
Describes the emergency OFF switch function.
Identifies the electric starter button.
Identifies the electric starter button for EXC AU.
Explains the indicator lamps on EXC models.
Explains the indicator lamps on XC-W models.
Details how to open the fuel filler cap safely.
Details how to close the fuel filler cap.
Explains the operation of the fuel tap.
Describes the choke lever and its function.
Identifies the shift lever and gear positions.
Identifies the kick starter and its operation.
Identifies the foot brake lever and its function.
Describes the side stand and its use.
Explains the steering lock mechanism.
Details the procedure for locking the steering.
Details the procedure for unlocking the steering.
Introduces the speedometer display and buttons.
Explains how to activate and test the speedometer.
Guides on setting the unit of measurement (km/miles).
Describes how to activate/deactivate speedometer functions.
Provides instructions for setting the clock time.
Explains how to view lap times.
Shows how to display current speed.
Explains how to display service hours.
Details navigation within the setup menu.
Guides on changing measurement units (km/miles).
Shows how to display the current time.
Provides detailed steps for setting the clock.
Explains how to time lap with the stopwatch.
Guides on viewing recorded lap times.
Shows how to display the total traveled distance.
Explains the trip master 1 function.
Explains the trip master 2 function.
Guides on setting trip master 2.
Explains how to display average speed 1.
Explains how to display average speed 2.
Explains the stop watch 1 function.
Explains the stop watch 2 function.
Summarizes speedometer functions and button operations.
Lists conditions for activating speedometer menus.
Provides essential advice before the first use of the motorcycle.
Details the procedure for running in the engine.
Outlines preparations for challenging riding environments.
Specific preparations for riding on dry sand.
Specific preparations for riding on wet sand.
Specific preparations for wet and muddy conditions.
Preparations for riding in hot weather and slow speeds.
Preparations for riding in cold weather or snow.
Lists pre-ride checks for safety and operation.
Provides instructions for starting the engine.
Guides on how to start moving the motorcycle.
Explains gear shifting and riding techniques.
Provides instructions and warnings about braking.
Details procedures for stopping and parking the motorcycle.
Guides on safely transporting the motorcycle.
Provides instructions and safety precautions for refueling.
Lists maintenance tasks at specific operating hour intervals.
Lists service tasks that can be ordered additionally.
Explains how to adjust suspension based on rider weight.
Explains high-speed and low-speed compression damping.
Guides on adjusting low-speed compression damping.
Guides on adjusting high-speed compression damping.
Guides on adjusting rebound damping of the shock absorber.
Details the process for measuring unloaded rear wheel sag.
Guides on checking the static sag of the shock absorber.
Details how to check the riding sag of the shock absorber.
Provides instructions for adjusting shock absorber spring preload.
Guides on adjusting the riding sag by changing springs.
Explains how to check the basic fork setting.
Guides on adjusting fork compression damping.
Guides on adjusting fork rebound damping.
Details adjusting fork spring preload.
Explains handlebar mounting options.
Guides on adjusting handlebar position for comfort.
Instructions for safely lifting the motorcycle.
Steps for safely removing the motorcycle from a lift stand.
Procedure for bleeding air from fork legs.
How to clean fork dust boots to prevent seal damage.
Steps to remove the fork protector.
Steps to install the fork protector.
Procedure for removing the fork legs.
Procedure for installing the fork legs.
Steps to remove the lower triple clamp for specific models.
Steps to remove lower triple clamp for EXC models.
Steps to install lower triple clamp for specific models.
Steps to install lower triple clamp for EXC models.
How to check for play in the steering head bearing.
Guides on adjusting steering head bearing play.
Procedure for greasing the steering head bearing.
Steps to remove the front fender.
Steps to install the front fender.
Procedure for removing the shock absorber.
Procedure for installing the shock absorber.
Steps to remove the motorcycle seat.
Steps to mount the motorcycle seat.
Steps to remove the air filter box lid.
Steps to install the air filter box lid.
Procedure for removing the air filter.
Procedure for installing the air filter.
Guides on cleaning the air filter and its box.
Procedure for sealing the air filter box.
Steps to remove the main silencer.
Steps to install the main silencer.
Details on changing the silencer's internal packing.
Procedure for removing the fuel tank.
Procedure for installing the fuel tank.
How to check the chain for dirt and cleaning needs.
Guides on cleaning the drive chain.
How to check and the importance of correct chain tension.
Guides on adjusting chain tension and rear wheel alignment.
Inspecting wear on drivetrain components.
How to check the frame for damage or deformation.
How to inspect the swingarm for damage.
Verifying correct routing of throttle cables.
Inspecting rubber grips for damage or wear.
Securing rubber grips with wire.
Guides on adjusting clutch lever position.
How to check and correct hydraulic clutch fluid level.
Procedure for changing hydraulic clutch fluid.
Steps to remove the engine guard.
Steps to install the engine guard.
How to check hand brake lever free travel.
Guides on adjusting hand brake lever free travel.
Guides on adjusting hand brake lever position.
How to check brake disc wear and for damage.
How to check the front brake fluid level.
Guides on adding front brake fluid.
How to check front brake lining thickness and for damage.
Procedure for changing front brake linings.
How to check foot brake lever free travel.
Guides on adjusting foot brake lever position.
How to check the rear brake fluid level.
Guides on adding rear brake fluid.
How to check rear brake lining thickness and for damage.
Procedure for changing rear brake linings.
Procedure for removing the front wheel.
Procedure for installing the front wheel.
Procedure for removing the rear wheel.
Procedure for installing the rear wheel.
How to inspect tires for wear and damage.
Guides on checking and correcting tire air pressure.
How to check and adjust spoke tension.
Steps to safely remove the battery.
Steps to safely install the battery.
Instructions for recharging the motorcycle battery.
Procedure for changing the main fuse.
Steps to remove the headlight assembly.
Steps to refit the headlight assembly.
Procedure for replacing the headlight bulb.
Procedure for replacing turn signal bulbs.
How to check and adjust headlight aim.
Guides on adjusting the headlight range.
Procedure for replacing the speedometer battery.
Explains the function of the cooling system.
How to check antifreeze and coolant levels.
Detailed steps for checking coolant level.
Procedure for draining the coolant.
Guides on refilling the cooling system with coolant.
How to check throttle cable play for smooth operation.
Guides on adjusting throttle cable play.
Explains the importance of correct idle settings.
Guides on adjusting carburetor idle speed.
Procedure for emptying the carburetor float chamber.
How to check shift lever position relative to boot.
Guides on adjusting shift lever position.
Explains auxiliary spring types for engine tuning.
Guides on setting the auxiliary spring for engine characteristic.
How to check the engine's gear oil level.
Procedure for changing the gear oil.
Steps to drain the gear oil.
Guides on refilling with gear oil.
How to add gear oil and check the level.
Detailed instructions for cleaning the motorcycle.
Maintenance steps for winter storage and operation.
Provides actions for longer-term storage.
Steps to prepare the motorcycle after storage.
Engine technical data for 125, 200, 250, 300 models.
Torque specifications for engine fasteners for 125/200 and 250/300 models.
Lists fluid capacities for coolant, oil, and fuel.
Technical data for chassis components like frame, suspension, brakes.
Technical data for fork settings and components for various models.
Technical data for shock absorber settings and components.
Torque specifications for chassis fasteners.
Technical data for carburetor settings across different models.
Tuning data for 125 models based on altitude and temperature.
Tuning data for 200 models based on altitude and temperature.
Tuning data for 200 models based on altitude and temperature.
Tuning data for 250 models based on altitude and temperature.
Tuning data for 300 models based on altitude and temperature.
Tuning data for 300 EXC BR based on altitude and temperature.
General information on carburetor tuning and needle positions.
Specifications and recommended suppliers for brake fluid.
Specifications, mixture ratio, and recommended supplier for coolant.
Specifications and recommended supplier for 4-stroke engine oil.
Specifications and recommended supplier for 2-stroke engine oil.
Specifications and recommended supplier for fork oil.
Specifications and recommended supplier for hydraulic fluid.
Specifications and recommended supplier for shock absorber fluid.
Fuel grade specifications, ethanol content, and warnings.
Recommended cleaner for air filters.
Recommended cleaner for motorcycle chains.
Recommended fuel stabilizer.
Recommended adhesive for grips.
Recommended high viscosity grease.
Recommended long-life grease.
Recommended cleaner for the motorcycle.
Recommended chain spray for off-road use.
Recommended oil for foam air filters.
Recommended products for protecting surfaces.
Recommended cleaner for various surfaces.
Recommended universal oil spray.
Explanation of the JASO T903 MA standard for 4-stroke engines.
Explanation of SAE viscosity classes for oils.
Explanation of the JASO FD standard for 2-stroke engine oils.
Explains error indicator symbols.
Explains information indicator symbols.
Explains the meaning of specific symbols used in the manual.
Explains the typographical formats used in the document.
Defines the intended use for EXC and XC-W models.
General safety instructions for operating the vehicle.
Explains different degrees of risk and their associated symbols.
Warns against tampering with the noise control system.
Provides guidelines for safe operation of the motorcycle.
Emphasizes the importance of wearing protective clothing.
Outlines rules for performing work on the vehicle.
Discusses responsible use and environmental considerations.
Highlights the importance of reading and keeping the owner's manual.
Details conditions for guarantee and warranty claims.
Information on fuel, lubricants, and environmental hazards.
Advises on using approved spare parts and accessories.
Emphasizes the importance of proper service and maintenance.
Notes that figures may show special equipment or be simplified.
Information on contacting authorized KTM dealers.
Illustrates the front-left view of the motorcycle with numbered parts.
Illustrates the rear-right view of the motorcycle with numbered parts.
Shows the location of the chassis number.
Shows the location of the type label.
Shows the location of the key number.
Shows the location of the engine number.
Shows the location of the fork part number.
Shows the location of the shock absorber part number.
Describes the clutch lever for different models.
Identifies the hand brake lever and its function.
Identifies the throttle grip.
Explains the kill switch function and states.
Explains the kill switch function and states for XC-W.
Identifies the horn button and its operation.
Explains the light switch functions.
Explains the light switch functions for XC-W.
Explains the turn signal switch operation.
Describes the emergency OFF switch function.
Identifies the electric starter button.
Identifies the electric starter button for EXC AU.
Explains the indicator lamps on EXC models.
Explains the indicator lamps on XC-W models.
Details how to open the fuel filler cap safely.
Details how to close the fuel filler cap.
Explains the operation of the fuel tap.
Describes the choke lever and its function.
Identifies the shift lever and gear positions.
Identifies the kick starter and its operation.
Identifies the foot brake lever and its function.
Describes the side stand and its use.
Explains the steering lock mechanism.
Details the procedure for locking the steering.
Details the procedure for unlocking the steering.
Introduces the speedometer display and buttons.
Explains how to activate and test the speedometer.
Guides on setting the unit of measurement (km/miles).
Describes how to activate/deactivate speedometer functions.
Provides instructions for setting the clock time.
Explains how to view lap times.
Shows how to display current speed.
Explains how to display service hours.
Details navigation within the setup menu.
Guides on changing measurement units (km/miles).
Shows how to display the current time.
Provides detailed steps for setting the clock.
Explains how to time lap with the stopwatch.
Guides on viewing recorded lap times.
Shows how to display the total traveled distance.
Explains the trip master 1 function.
Explains the trip master 2 function.
Guides on setting trip master 2.
Explains how to display average speed 1.
Explains how to display average speed 2.
Explains the stop watch 1 function.
Explains the stop watch 2 function.
Summarizes speedometer functions and button operations.
Lists conditions for activating speedometer menus.
Provides essential advice before the first use of the motorcycle.
Details the procedure for running in the engine.
Outlines preparations for challenging riding environments.
Specific preparations for riding on dry sand.
Specific preparations for riding on wet sand.
Specific preparations for wet and muddy conditions.
Preparations for riding in hot weather and slow speeds.
Preparations for riding in cold weather or snow.
Lists pre-ride checks for safety and operation.
Provides instructions for starting the engine.
Guides on how to start moving the motorcycle.
Explains gear shifting and riding techniques.
Provides instructions and warnings about braking.
Details procedures for stopping and parking the motorcycle.
Guides on safely transporting the motorcycle.
Provides instructions and safety precautions for refueling.
Lists maintenance tasks at specific operating hour intervals.
Lists service tasks that can be ordered additionally.
Explains how to adjust suspension based on rider weight.
Explains high-speed and low-speed compression damping.
Guides on adjusting low-speed compression damping.
Guides on adjusting high-speed compression damping.
Guides on adjusting rebound damping of the shock absorber.
Details the process for measuring unloaded rear wheel sag.
Guides on checking the static sag of the shock absorber.
Details how to check the riding sag of the shock absorber.
Provides instructions for adjusting shock absorber spring preload.
Guides on adjusting the riding sag by changing springs.
Explains how to check the basic fork setting.
Guides on adjusting fork compression damping.
Guides on adjusting fork rebound damping.
Details adjusting fork spring preload.
Explains handlebar mounting options.
Guides on adjusting handlebar position for comfort.
Instructions for safely lifting the motorcycle.
Steps for safely removing the motorcycle from a lift stand.
Procedure for bleeding air from fork legs.
How to clean fork dust boots to prevent seal damage.
Steps to remove the fork protector.
Steps to install the fork protector.
Procedure for removing the fork legs.
Procedure for installing the fork legs.
Steps to remove the lower triple clamp for specific models.
Steps to remove lower triple clamp for EXC models.
Steps to install lower triple clamp for specific models.
Steps to install lower triple clamp for EXC models.
How to check for play in the steering head bearing.
Guides on adjusting steering head bearing play.
Procedure for greasing the steering head bearing.
Steps to remove the front fender.
Steps to install the front fender.
Procedure for removing the shock absorber.
Procedure for installing the shock absorber.
Steps to remove the motorcycle seat.
Steps to mount the motorcycle seat.
Steps to remove the air filter box lid.
Steps to install the air filter box lid.
Procedure for removing the air filter.
Procedure for installing the air filter.
Guides on cleaning the air filter and its box.
Procedure for sealing the air filter box.
Steps to remove the main silencer.
Steps to install the main silencer.
Details on changing the silencer's internal packing.
Procedure for removing the fuel tank.
Procedure for installing the fuel tank.
How to check the chain for dirt and cleaning needs.
Guides on cleaning the drive chain.
How to check and the importance of correct chain tension.
Guides on adjusting chain tension and rear wheel alignment.
Inspecting wear on drivetrain components.
How to check the frame for damage or deformation.
How to inspect the swingarm for damage.
Verifying correct routing of throttle cables.
Inspecting rubber grips for damage or wear.
Securing rubber grips with wire.
Guides on adjusting clutch lever position.
How to check and correct hydraulic clutch fluid level.
Procedure for changing hydraulic clutch fluid.
Steps to remove the engine guard.
Steps to install the engine guard.
How to check hand brake lever free travel.
Guides on adjusting hand brake lever free travel.
Guides on adjusting hand brake lever position.
How to check brake disc wear and for damage.
How to check the front brake fluid level.
Guides on adding front brake fluid.
How to check front brake lining thickness and for damage.
Procedure for changing front brake linings.
How to check foot brake lever free travel.
Guides on adjusting foot brake lever position.
How to check the rear brake fluid level.
Guides on adding rear brake fluid.
How to check rear brake lining thickness and for damage.
Procedure for changing rear brake linings.
Procedure for removing the front wheel.
Procedure for installing the front wheel.
Procedure for removing the rear wheel.
Procedure for installing the rear wheel.
How to inspect tires for wear and damage.
Guides on checking and correcting tire air pressure.
How to check and adjust spoke tension.
Steps to safely remove the battery.
Steps to safely install the battery.
Instructions for recharging the motorcycle battery.
Procedure for changing the main fuse.
Steps to remove the headlight assembly.
Steps to refit the headlight assembly.
Procedure for replacing the headlight bulb.
Procedure for replacing turn signal bulbs.
How to check and adjust headlight aim.
Guides on adjusting the headlight range.
Procedure for replacing the speedometer battery.
Explains the function of the cooling system.
How to check antifreeze and coolant levels.
Detailed steps for checking coolant level.
Procedure for draining the coolant.
Guides on refilling the cooling system with coolant.
How to check throttle cable play for smooth operation.
Guides on adjusting throttle cable play.
Explains the importance of correct idle settings.
Guides on adjusting carburetor idle speed.
Procedure for emptying the carburetor float chamber.
How to check shift lever position relative to boot.
Guides on adjusting shift lever position.
Explains auxiliary spring types for engine tuning.
Guides on setting the auxiliary spring for engine characteristic.
How to check the engine's gear oil level.
Procedure for changing the gear oil.
Steps to drain the gear oil.
Guides on refilling with gear oil.
How to add gear oil and check the level.
Detailed instructions for cleaning the motorcycle.
Maintenance steps for winter storage and operation.
Provides actions for longer-term storage.
Steps to prepare the motorcycle after storage.
Engine technical data for 125, 200, 250, 300 models.
Torque specifications for engine fasteners for 125/200 and 250/300 models.
Lists fluid capacities for coolant, oil, and fuel.
Technical data for chassis components like frame, suspension, brakes.
Technical data for fork settings and components for various models.
Technical data for shock absorber settings and components.
Torque specifications for chassis fasteners.
Technical data for carburetor settings across different models.
Tuning data for 125 models based on altitude and temperature.
Tuning data for 200 models based on altitude and temperature.
Tuning data for 200 models based on altitude and temperature.
Tuning data for 250 models based on altitude and temperature.
Tuning data for 300 models based on altitude and temperature.
Tuning data for 300 EXC BR based on altitude and temperature.
General information on carburetor tuning and needle positions.
Specifications and recommended suppliers for brake fluid.
Specifications, mixture ratio, and recommended supplier for coolant.
Specifications and recommended supplier for 4-stroke engine oil.
Specifications and recommended supplier for 2-stroke engine oil.
Specifications and recommended supplier for fork oil.
Specifications and recommended supplier for hydraulic fluid.
Specifications and recommended supplier for shock absorber fluid.
Fuel grade specifications, ethanol content, and warnings.
Recommended cleaner for air filters.
Recommended cleaner for motorcycle chains.
Recommended fuel stabilizer.
Recommended adhesive for grips.
Recommended high viscosity grease.
Recommended long-life grease.
Recommended cleaner for the motorcycle.
Recommended chain spray for off-road use.
Recommended oil for foam air filters.
Recommended products for protecting surfaces.
Recommended cleaner for various surfaces.
Recommended universal oil spray.
Explanation of the JASO T903 MA standard for 4-stroke engines.
Explanation of SAE viscosity classes for oils.
Explanation of the JASO FD standard for 2-stroke engine oils.
Explains error indicator symbols.
Explains information indicator symbols.
General| Starter | Kickstarter |
|---|---|
| Transmission | 6-speed |
| Front Brake | Disc brake |
| Rear Brake | Disc brake |
| Cooling System | Liquid-cooled |
| Engine Type | 2-stroke |
To Next Page
