EasyManuals Logo

Lamtec FMS Series User Manual

Lamtec FMS Series
162 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #29 background imageLoading...
Page #29 background image
Settings List of Parameters
(Level 0 and 1 parameters only)
Para- Short Safety Lower Upper
meter- design- level limit limit Standard
No. nation Description values Aids
_____________________________________________________________________________________________________
1 P30
897 O2Stoer 1 0 2 O
2
0 P31
898 O2-TotZ 0 3 20 15 P32
899 O2-P-Fak 0 1 50 O P-factor 5 P32
2
900 O2 TZ - 0 0 5 O
2
3 P32
901 O2Neutr1 1 0 1000 Correction value output on deactivated
O regulation. Fuel 1 300 P31
2
902 O2Neutr2 1 0 1000 Correction value output on deactivated
O regulation. Fuel 2 300 P31
2
903 O2FWZeit 1 0 9999 O deactivated after fuel
2
change in sec.. 30 P33
904 O2WarteZ 1 0 9999 O regulation active after
2
ignition in sec. 90 P34
910 O2Totbnd 2 0 10 O lag band in 0.1% 2
2
914 O2Aktiv 0 0 999 Activate O regulation from
2
load position X (in pts) 0 P35
915 O2Deakti 0 0 999 Deactivate O regulation from
2
load position X (in pts) 999 P35
917 LftmKor1 1 0 999 Air shortage correction value, fuel 1 150 P31
918 LftmKor2 1 0 999 Air shortage correction value, fuel 2 150 P31
919 O2 4mA 1 0 999 O value 4mA 0 P36
2
920 O2 20mA 1 0 999 O value 20mA 250 P36
2
931 O22UBU1G 1 0 250
100 P37
932 O22UBU1V 1 0 250
100 P37
933 O22UBU2G 1 0 250
100 P37
934 O22UBU2V 1 0 250
100 P37
936 O2SOWert 0 0 65535 2 P38
Parameter for O regulation
2
896 O2Regler 0 0 9 O -Regulator
2
0 = O regulator off 8 = Only display, base value
2
1 = Standard regulator for deact. O regulator
2
2 = Without lag time 9 = Only display, base value
3 = only display for air shortage
neutral value
Error shut-down by regulator
permitted (0=No, 1=on air shortage)
Lag time of the O regulation section
2
Lag time shortening of the regulation
section with full load
Lower 2nd monitoring band, fuel 1
in % of target value, base load
Lower 2nd monitoring band, fuel 1
in % of target value, full load
Lower 2nd monitoring band, fuel 2
in % of target value, base load
Lower 2nd monitoring band, fuel 2
in % of target value, full load
Probe dynamic test
29

Table of Contents

Other manuals for Lamtec FMS Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Lamtec FMS Series and is the answer not in the manual?

Lamtec FMS Series Specifications

General IconGeneral
BrandLamtec
ModelFMS Series
CategoryController
LanguageEnglish

Related product manuals