Table of Contents
3
Instrumentation for commissioning 72
O regulation 49 - 62
2
Adjusting load ratings individually 73
Automatic functions control
Entering an initial curve 73
during operation 49 - 50
Approaching control elements from one side 74
Adjusting the integrated O regulator (optional) 49
2
Entering settings 74
Checks during burner start-up 49
Entering top setting 74
O monitoring bands 49
2
Ignition delay when setting 74
O boundary curves 49
2
Pre-setting load automatically 74
Dynamic probe test 50
Entering the compound curves
Probe blockage 50
with the burner stationary 75
Correction output monitoring 50
Keeping the re-circulation damper
Regulation strategy 51 - 53
closed in pre-ventilation 75
With pre-setting for load changes 52
Setting the pilot burner (servicing mode) 75
Extended regulation strategy (air shortage) 53
Switching the burner on again
via the target value 75
Connection to O meter 54
2
Via analogue interface 54
Operator controls and display 55 - 56
System Operation 76 - 89
Mode switching 55
Mode display 76 - 78
Calling up O regulation text messages 56
2
Significance of modes on the FMS 76 - 77
O regulator modes 77
Commissioning 57 - 61
2
"ES" Mode progress (set-control) 78
Setting the correction range 57
Continue programming 78
Inputting the O target value curve 58
2
Calling up the correction range set 59
Calculation and setting of
4 Curve sets FMS (option) 79
control parameters-(manual) 59
Interconnection with 4 curve sets option 79
Lag time (parameters 898/900) 60
P-factor (parameter 899) 60
Checksums
Setting base value for "Deactivated
Running time meter 80
control” and "Air shortage” 61
Recalling the checksums
Calling up the base value for O regulation
2
and the safety times 80
deactivated/air shortage 61
Calling up running time meter 80
Automatic 61
Operation 62
Messages / Faults 81 - 89
The meaning of the additional modes 62
What happens in the event of FMS fault 81
Calling up O regulation text messages 62
2
Reading off a fault 81
Resetting a fault 81
Correction 63 - 66
Calling up fault history 81
Set correction input 63 - 65
O regulation perturbed 82
2
Setting the correction range 65
Air shortage perturbation 82
Recall set correction range 65
Resetting O errors 82
2
Altering the correction range 66
Calling up O regulation error history 82
2
Correction modes 66
Fault codes 83 - 89
Run to shut-off limits 67 - 70
FMS Fault Correction
Run to shut-off limits 67
Aids 90 - 115
Checking the shut-off limits at the
General Faults (A) 90 - 94
three/point step output of the FMS 67
Three-point step control output (B) 95 - 96
Checking the shut-off limits at
continuous output of the FMS 68
Continuous output (C) 97
Tolerance limits direction air deficiency 69
Load signal (D) 98 - 99
Indication for an example protocol 69
Feedback (E) 100 - 103
Checking the O influence 69
2
Correction input (F) 104 - 105
Example protocol 70
Digital inputs (G) 106
Control unit faults (H) 107
Tips & Tricks 71 - 75
Leakage test 108
Programming 1st point
(ignition load point) 71
Parameters (P) 109 - 118
Programming with burner running 71 - 72
Programming with burner stationary 72
Reversing the programming 72
To Next Page
Loading...
Need help?
General
