LDARtools phx42 - Certifications and Markings; General Specifications; Electrical Parameters; Battery and Charging

UNCONTROLLED IF PRINTED 46
Rev2.06
3/30/2021
Edited Manual Calibration, new External Parts photo, H
2
Quick fill and Charging
port Tech Tip, new Tool Kit photo, added tools to Tool Kit list, added Probe Test
Adapter section, moved and edited Probe Care and Routing section, edited
Power Button Section, Edited Charging the phx42 Section, removed all reference
to “Gas Check”, Edited Filter Detection Section, Application Error Codes updated.
Edited Firewall Whitelist.
Rev2.07
8/5/2021
Updated Level 1 Tech Pledge, updated “Required Spare Parts” list (pg. 25)
according to Pledge revisions, edited “Level One” to “Level 1” throughout
document, edited “Hydrogen” to “H
2
” throughout document, edited “Spanbox5”
to “SpanBox5” (pg. 20), edited “glow disk” to “Glow Disk” throughout document,
edited “Self-Check” to “Self-check” / “self-check” depending on use and
placement throughout document
Rev2.08
9/7/2021
Removed, “Sleep mode, connected, disconnected, or ignited are all ok. In some
cases, a flameout will occur. This is normal,” from step 3 of the Fill Adapter
Maintenance section under Filling the phx42 with H
2
on page 9.
Rev2.09
11/11/2021
Updated any references to “42 app” to “phxApp.” Added Tech Tip regarding
Ultra High Pure (99.999%) H
2
to Filling procedure on pg. 9; removed individual
Level 1 repair procedures from section 3, added list of Level 1 repair work
instructions linked to corresponding documentation; enlarged internal
components diagram in section 3 on pg. 26, added “Internal” to section header;
updated contents to reflect changes; updated tool kit inventory photo,
rearranged parts list accordingly; added spare parts kit part number; revised
online training access instructions. Changed “Sample Flow” to “Probe Flow” on
page 39. Changed recommended probe flow rate to ≥0.12 Liters/minute on page
39 with note stating to report an issue if probe flow rate drops below 0.12
Liters/minute. Removed table below “Responding to failed filter calibration
section on page 20. Removed right-most column on the “Accuracy and Linear
Range” row of the phx42 Operating Parameters table on page 32.
Rev2.10
12/2/2021
Added step instructing to allow for 15-minute warm-up period after step 3 to
Manual Calibration section (pg. 19).
Rev2.11
12/6/2021
Added customer support registration instructions (pg. 28), revised user login
information page (pg. 29) with new hyperlinks and directories and added
specifics to assist with registration for first-time users. Removed specific
references to Litmos.
Rev2.12
1/5/2022
Relocated Technical Support section (formerly Section 4) up to page 2—original
pg. 2 Technical Support page featured same content as first page of original
Section 4 Tech Support; changed all references to “Customer Support Portal” to
“Customer Portal”; added text to Self-check section step 4.a (pg. 21) informing
user not to type anything in the event of regular daily/weekly self-check
procedures; added list of scenarios requiring internet connection (pg. 16);
added list of negative PPM value errors (pg. 24).
Rev2.13
1/7/2022
Relocated (and edited) Tech Tip regarding reporting an issue in the event any
operating parameter is outside of the published range on pg. 21; changed
recommended probe flow rate on pg. 32 from ≥ 0.12 Liters/minute to 0.2 to 0.35
Liters/minute.
Rev2.14
1/19/2022
Updated Firewall Whitelist (pg. 5) as per K. Moses and K. Regan’s specifications.
Rev2.15
1/26/2022
Removed cal.ldartools.com and api.splashtop.com from the Firewall Whitelist as
per K. Moses’ request, revised “Scrubber Medium” to “Scrubber Media” where
stated.
Rev2.16
3/15/2022
Revised online training instructions for LMS change (pg. 4, 27), updated
whitelist to remove Litmos domain and add the talentLMS domain (pg. 5).
Rev2.17
4/13/2022
Added text regarding to replacing probe tip filter to FAQs while Monitoring (pg.
15).