EasyManuals Logo

LG STB-3000 Setup Guide

LG STB-3000
86 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #38 background imageLoading...
Page #38 background image
38
206-4272
100 - VIDEO INTERFAC
Selects the HDMI port on the display panel to be used for HDMI
input from the STB. Set to 3 for HDMI 1 (default). Set to 4 for
HDMI 2. Set to 5 for HDMI 3.
If you change the value of this item, make sure to reconnect the
HDMI cable from the STB to the appropriate HDMI port on the
display panel once you have exited the Installer Menu.
101 - IR FEEDBACK
If set to 0, the STB’s Bluetooth feature is enabled (default). If set
to 2, the Bluetooth feature is disabled.
Note: Bluetooth may be used in selected installation environments,
with Bluetooth enabled devices, for example, an LG Magic Motion
Remote (MMR). However, depending on the application for which
the STB is installed, you may need to disable Bluetooth.
102 - ATSC BAND
Sets up STB to receive different types of incoming signals.
0 = Broadcast 1 = CATV 2 = HRC
3 = IRC 4 = Same as NTSC
103 - ATSC TUNE MODE
Sets ATSC tuning mode. Default set to 1 for Physical Channel
scan. Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets Minor Start Channel number at power up. 0 = NTSC. If not
0, number selected is the digital channel’s Minor Start Channel
number.
Note: This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 0 or 255.
105 - VID OUT FORMAT
Selects the format for video output (i.e., the resolution):
1 = 720p (default) 4 = 1080p 5 = 1366 x 768
If you change the video output format on location, once you exit
the STB Installer Menu, a Changing Video Output Resolution
pop-up banner will appear at the bottom of the display screen,
and then the STB will reboot to change the resolution per your
selection. When the reboot is complete, a conrmation pop-up
banner for the new video output resolution will be displayed. To
conrm the new video output resolution, use the arrow keys on
the Installer Remote to select YES in the conrmation banner, and
then press OK on the Installer Remote.
If there is no user interaction within 10 seconds of the prompt for
conrmation, or if you select “NO” in the conrmation banner, the
STB will reboot and revert to the former resolution.
Note: If this item is updated via a TLX le loaded on a Pro:Centric
server, no conrmation is required.
Note: Refer to documentation for the applicable display panel(s)
to determine the appropriate resolution setting. The selected
resolution should be compatible with the display panel’s native
video output resolution. If necessary/desired, you can use TV Zone
designations to create multiple proles to differentiate item 105
settings by display panel brand. See Reference section, “Using the
STB’s Zoning Features,” for further information on TV Zones.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to
retain default aspect ratio with power off. See item 096 DEF. ASP.
RATIO above.
108 - PANEL COM (Panel Communication)
Sets the display panel baud rate:
0 = 1200 1 = 2400
2 = 9600 (default) 3 = 115200
110 - PANEL DELAY
After the STB sends the turn ON command to the display panel,
the display panel requires time to complete its power on sequence
before it begins accepting commands from the STB. This item sets
the time, in seconds, to delay the STB’s initial communication with
the display panel. The default value is 8 seconds.
Note: The amount of time required for the display’s power on
sequence varies by display panel brand/model. Thus, depending
on the brand/model of display panel connected to the STB, you
may be able to decrease or you may need to increase the Panel
Delay value, accordingly.
Note: This item does not apply to LG Hospitality display panels.
111 - PANEL VOL PRE (Panel Volume Preset)
Determines a preset xed volume level (gain) to set in the display
panel. The audio signal (volume level) is dynamically controlled
in the STB. The default value is 100 to provide a typical 1:1 ratio
of volume level to sound output when the STB is connected to an
LG display panel.
Note: Sound output may vary by display panel brand/model. Thus,
depending on the brand/model of display panel connected to the
STB, you may need to adjust the preset volume level to achieve
the desired sound output.
113 - PANEL TYPE
Sets the TLM command set to communicate with the display
panel. This setting is only applicable for LG Public Display TVs
and Commercial Monitors that use the RS-232C TELEVISION
CONTROL port for STB-to-display panel communication. The
default value (4) will be appropriate for most current display
models. See Reference section, “Display Panel Specications,” to
determine the appropriate setting for the display panel being used.
116 - VIDEO MUTE EN (Video Mute Enable)
Applicable for analog channels only. If set to 1, video mutes
(blank screen) when no signal is present.
Installer Menu (Cont.)

Table of Contents

Other manuals for LG STB-3000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the LG STB-3000 and is the answer not in the manual?

LG STB-3000 Specifications

General IconGeneral
BrandLG
ModelSTB-3000
CategorySet-top boxes
LanguageEnglish

Related product manuals