Life GE UNI R - Maintenance and Care; Maintenance Instructions and Warnings

H
S
I
L
G
N
E
11
MAINTENANCE
11.1
Maintenance instructions and warnings
•
O
nce the automation has been tested, the parameters set must not be altered. If further adjustments (e.g. alterations to the voltage value) are made, ALL THE CHECKS REQUIRED FOR
TESTING AND COMPLIANCE WITH STANDARDS MUST BE REPEATED.
•
The Manufacturer declines responsibility for damage or injury caused by non-compliance with the information provided in this manual and the safety instructions provided below.
•
The Manufacturer declines all responsibility for damage and malfunctions deriving from non-compliance with the maintenance instructions.
•
In order to keep the operator effi cient and safe, follow the cleaning, checking and routine maintenance procedures as described in this manual. This is the owner’s duty.
•
Any checking, maintenance or repair work must be conducted by a PROFESSIONAL FITTER
•
Always switch off the electricity supply in the event of malfunctions, breakdowns and before any other operations in order to avoid the gate from being activated.
•
Always disconnect the operator’s power supply before performing any maintenance or cleaning operation.
•
The owner is not authorised to remove the control unit cover as it contains live parts.
•
If the power cable is damaged, it must be replaced by the Manufacturer or its technical Assistance service or in any case a person with a similar qualifi cation in order to avoid risks.
•
Use original spare parts, accessories and clamping material only.
•
D
o not perform technical or programming modifi cations on the control unit. Operations of this type may cause malfunctions and/or risk of accidents. The Manufacturer declines responsibility for damage
deriving from modifi ed products.
•
In the event of intervention of automatic or fuse switches, before restoring function conditions identify and eliminate the fault. Request the intervention of a PROFESSIONAL FITTER.
•
The disconnection and replacement of the pair of buffer batteries (optional) may be performed by a PROFESSIONAL FITTER only.
•
If a fault that cannot be solved following the information contained in the present manual arises, contact the manufacturer’s assistance service.
•
All maintenance, repair or replacement of parts must be recorded in the maintenance log, which is SUPPLIED AND INITIALLY FILLED IN BY THE FITTER.
11.2
Routine maintenance
Every 6 months a PROFESSIONAL FITTER should repeat the series of tests described for automation testing (see INSTALLATION MANUAL – TESTING AND TRIAL RUN Chap. ).
12
DEMOLITION AND DISPOSAL
•
T
he control unit is constructed using various materials, which implies the adoption of different disposal procedures. Refer to regulations in force in the country in which the automation is installed,
especially with regard to the buffer batteries (if present).
•
If present the batteries must be removed from the control unit prior to disposal. Disconnect the control unit from the electricity supply before removing batteries.
Contact qualifi ed fi rms for disposal.
ATTENTION: operator disconnection from the mains supply must be performed by a qualifi ed electrician using suitable tools.
13 MANUFACTURER’S DECLARATION OF CONFORMITY
Declaration of conformity
under Directive 98/37/EC, appendix II, part B (Manufacturer’s Declaration of CE Conformity).
LIFE home integration
Via 1 Maggio, 37
31043 FONTANELLE (TV) – Italy
declares that the following product:
GE UNI R control unit
satisfi es the essential requisites established in the following directives:
•
Low voltage directive 73/23/EEC and subsequent amendments,
•
Electromagnetic compatibility directive 89/336/EEC and subsequent amendments,
•
Radio and telecommunications equipment directive 1999/5/EC and subsequent amendments.
and satisfi es the following standards:
•
EN 12445:2000 Industrial, commercial and garage doors and gates – Safety in the usage of motorised doors – testing methods
•
EN 12453: Industrial, commercial and garage doors and gates – Safety in the usage of motorised doors - Requisites.
•
EN 60204-1:1997 Machinery safety – Electric equipment of the machine – Part 1: general rules.
•
EN 60950 Information technology equipment - Safety - Part 1: General requisites
•
ETSI EN 301489-3:2001 Electromagnetic compatibility for radio equipment and appliances.
•
EN 300220-3:2000
Radio equipment and systems – short band devices – Technical characteristics and testing methods for radio apparatus with a frequency of 25 to 1000 MHz and powers of up to 500mW.
The Manufacturer also declares that it is not permitted for the abovementioned components to be used until such time as the system in which they are incorporated is declared conform to directive 98/37/EC.
Fontanelle ____________ Name of Signor: Faustino Lucchetta
Position:
Managing Director
Signature: __________________
2
9