Page 160 of 192
Mounting
Do not mount the battery upside down.
Please follow the mounting instructions of the control box e.g. CBJ Care or COBO.
Standby mode
When the BAJL Li-Ion is not being used for a longer period - more than a week - or when it is on stock, it enters into a standby mode to save power
and protect the battery from deep discharge.
• Please connect the charger for approx. 15 seconds to exit the standby mode before use.
• There is no audio signal to indicate the standby mode or to indicate exit of standby mode.
After exit of the standby mode
If there is still no power on, the battery needs to be charged.
After charging, the hand control and/or the control box will indicate the battery capacity level again
Deep discharge protection
The BAJL Li-Ion has a deep discharge protection to extend the battery lifetime. The deep discharge protection is activated when the battery is discharged.
• Please connect the charger for approx. 15 seconds to exit the deep discharge mode before use.
If the battery is completely discharged, the charging will be started at a very small rate to protect the battery. This small charging rate is not sufficient
to turn on the light in the charger, and therefore the user may believe that the system has not yet started. Depending on the battery state, it may
take several hours to get to the normal charging state. The orange light of the control box will not be turned on as the operation is analogue. It is
therefore not possible to see that the charging has started, however, only at a low level.
If any of the lithium ion batteries built into LINAK products is found to be defective under warranty, LINAK will provide a new product to the OEM.
LINAK explicitly disclaims all other remedies. LINAK shall not in any event be liable under any circumstances for any special indirect punitive incidental
or consequential damages or losses arising from any incident related to the inherent risk of thermal runaway in the lithium ion cell and any use of
LINAK products. Moreover, LINAK explicitly disclaims lost profits, failure to realise expected savings, any claim against our customer by a third party,
or any other commercial or economic losses of any kind, even if LINAK has been advised of the possibility of such damages or losses.
Transportation
The lithium ion batteries must be packed and transported according to applicable regulations. Always ask your local transportation provider how to
handle the transportation of lithium ion batteries.
Recommendations:
• Do not exceed the storage temperature as it will shorten the lifetime and performance.
• Allow the battery to settle to the temperature specified in the user manual before use or charging.
• Only use correct LINAK charger (CHJ2, CH01 or integrated charger in JUMBO control box).
• Do not exceed the duty cycle as it will shorten the life time and performance.
• BAJL Li-ion is not intended for use in outdoor applications and indoor pool environments.
• If the battery is completely discharged, then recharge the battery before storage.
• Unintentional use of the emergency button, e.g. short activation and deactivation of the emergency button after operating the actuators, can lead
to an error indication of remaining battery capacity. The battery capacity will however be shown correctly approx. 20 seconds after activation of the
emergency button.
• The BAJL goes into sleep mode approximately 20 seconds after the CBJ Care enters into sleep mode. If the CBJ Care is reactivated within this
period, it can lead to a wrong remaining battery capacity indication. The remaining battery capacity will however be shown correctly approx.
20 seconds after the reactivation of the CBJ Care.
Safety feature
BAJL Li-ion contains several mechanisms to protect itself from being damaged due to excessive use.
In case of overheating, the device will activate a thermal protection. No power output will be available until the temperature has returned to normal
operating range. Overheating may occur by extensive use at high temperature or by exceeding the duty cycle.
Battery safety
LINAK li-ion batteries for medical use are designed and manufactured to be safe through the product lifetime. LINAK has performed various tests
of the batteries in normal use, abuse situations and failure situations to verify the design and production methods. These tests have not shown any
unacceptable risks.
The batteries are also UL-tested to have an independent organisation verify the safety of the design and to obtain a safety certificate.
This means that UL regularly inspects the factory to check that standards are complied with.
UL has tested in accordance with the following standards:
UN38.3, 6
th
edition - Battery Transportation Safety
IEC62133 Battery Safety
UL2054, 2
nd
edition - Standard for Household and Commercial Batteries
To Next Page
Loading...
Need help?
General
