Menvier Security TS900+ - Default Chapter; Table of Contents

Contents
Overview ............................................. 1
Introduction ................................................ 1
System Architecture.................................... 1
Control Panel.............................................. 1
Remote Keypads ....................................... 2
32 Character LCD (NETLCD) ........................ 2
8 Character Starburst (NETSTAR)................... 2
4 Character LED (NETLED)............................ 2
Remote Arming Station (NETARM)................ 2
TSXNODE..................................................... 2
TS900 NODE (Obsolete) .............................. 2
ID Node (TS900 IDNODE)............................. 2
TS700 LEC ................................................... 2
Specifications............................................. 3
General....................................................... 3
Electrical ..................................................... 3
Physical ....................................................... 3
System Installation............................... 4
Cable Routing ............................................ 4
Node Network Wiring (TS900+ Only) ........... 4
Remote Network Wiring ..............................5
Combined Network Wiring (TS900+)........... 5
Control Panel Installation ............................ 6
Control Panel PCB Layout........................... 7
Connection Terminals & Indicators............. 8
Mains Connection...................................... 9
Battery Connection .................................... 9
Remote Keypads ....................................... 9
NETLCD Remote Keypad............................. 9
NETSTAR Remote Keypad ............................ 9
NETLED Remote Keypad ............................. 9
NETARM Remote Arming Station.................. 9
PCB Layouts & Connections........................ 9
Installation Procedure................................ 10
Engineer’s Keypad.................................... 11
XNode (TS900+) ....................................... 11
XNode Wiring ............................................ 11
Programmable Outputs on the XNode..... 11
Installing an XNode ................................... 13
TS900 Node Installation (TS900+ Only) .....13
TS900 Node Layout (Obsolete) ................. 13
TS700 LEC Installation ...............................14
Wiring Detection Circuits........................... 14
Double Pole ..............................................14
End Of Line................................................15
External Sounder Connections ................. 15
Installing an External Sounder from a XNode16
Auxiliary Tamper........................................17
Extension Loudspeakers............................17
Digicom/RedCARE Installation ..................17
Plug-on Digicom Installation .....................17
Plug-on digi-Modem Installation...............18
Output Modules Installation (CPA6.OM)....18
Connecting a Printer.................................18
Using the CPA6 Printer................................18
Using the DATAC / RS232 Printer.................19
Programmable Outputs............................20
Control Panel Outputs ...............................20
XNode Outputs..........................................20
Remote Keypads & TS700.LECs.................20
Installing a Monitored Power Supply .........21
Pre Power-Up Checks................................21
Initial Power-Up .........................................21
Power-Up Checks .....................................22
NVM Defaults ............................................22
Engineer’s Menu 1 .............................24
Introduction ..............................................24
Menu contents ..........................................24
Panel Outputs [1.1] .............................25
Digicom Outputs [1.2]............................25
Digicom Channels [1.3] ........................25
Programmable Output Types ...................25
Program Circuits [1.4].............................28
Circuit Types ..............................................28
Circuit Attributes.........................................29
System Timers [1.5] .............................30
Setting Modes [1.6] .............................33
Do System Print [1.7] .............................34
Remote Reset Algorithm [1.8] ................34
Configuration [1.9] .............................34
Goto User Menu 1 [1.0] ..........................37
Menu contents ..........................................37
View Location Text (LCD Only) [1.B] ........38
Relearn Hardware [1.C]..........................38
Engineers Menu 2..............................39
Introduction ..............................................39
Menu Contents..........................................39
View Circuits [2.1] .................................40
Set System Time [2.2] .............................40
Set System Date [2.3] .............................40
Change Passcode [2.4].........................40
Chime Circuits [2.5] .............................41