Miele PG 8593 - Page 7

To Next Page

To Previous Page

Contents

Technical data.................................................................................................................. 179

Caring for the environment ............................................................................................ 180

Disposal of the packing material ...................................................................................... 180

Main Page

Table of Contents3
Notes about These Instructions8
Definition of Terms8
Intended Use9
User Profiles10
Guide to the Machine11
Overview11
Control Panel12
Leds in Buttons13
Warning and Safety Instructions14
Symbols on the Machine19
Using the Machine20
Display Illustrations20
Switching on21
Switching off21
Auto-Off Function21
Ready for Use21
Display Interface22
Menu Operation22
Settings in the Menu23
Symbols on the Display24
Commissioning25
Installation and Connection25
Procedure25
Opening and Closing the Door29
Electronic Door Locking29
Opening the Door29
Closing the Door29
Opening the Door Using the Emergency Release30
Water Softener31
Water Hardness31
Setting the Water Hardness Level32
Filling the Salt Reservoir34
Add Salt Reminder36
Areas of Application37
Mobile Units, Baskets, Modules and Inserts37
Adjusting the Upper Basket38
Preparing the Load40
Chemical Processes and Technology44
Adding and Dispensing Chemical Agents48
Dispensing Systems48
Labelling of the Siphons48
DOS Modules49
Connecting DOS Modules49
Dispensing Liquids49
Neutralising Agent50
Refilling Neutralising Agent50
Refill Indicator51
Dispensing Neutralising Agent51
Cleaning Agent52
Replenishing Liquid Cleaning Agent52
Refill Indicator53
Dispensing Liquid Detergent53
Operation54
Selecting a Programme54
Starting a Programme54
Starting a Programme Using Delay Start54
Drying56
Programme Sequence Indicator58
At the End of the Programme58
Interrupting a Programme59
Cancelling a Programme60
Programme Cancelled Due to a Fault60
Cancelling a Programme Manually60
System Messages61
Changing the Filter61
Cleaning the Filter Combination62
Low Fill Levels62
Spray Pressure and Spray Arm Monitoring63
Settings64
Delay Start65
Drying66
DOS Venting68
Language69
Time of Day70
Volume73
Further Settings74
Code76
Enter Code76
Date79
Log Book81
Report82
Temperature Unit82
Programme Settings82
Air Cooling83
Release Programme84
Moving a Programme: Allocating Programme Selection Buttons85
Dispensing Systems86
DOS Venting87
Test Programme90
Filter Maintenance90
Cleaning the Filters in the Wash Cabinet90
Activating and Setting the Interval90
Interface92
Water Hardness95
Display: Temperature95
Display Brightness and Contrast96
Switch off after97
Ready for Operation97
Auto-Off Function97
Switching off after Activating98
Factory Default99
Software Version99
Programme Settings100
Adjusting Programme Settings100
Programme Structure100
Programme Header100
Programme Blocks101
Opening the Menu102
Reset Programme102
Altering a Programme103
Allocating Wash Blocks103
Spray Arm Monitoring104
Measuring Conductivity106
Change Water Quantity109
Increasing Drainage Time110
Setting the Concentration Level111
Set Wash Block Temperature112
Drying Unit114
Process Documentation118
Outputting Cycle Reports Retrospectively121
External Software121
Report Printer121
Maintenance122
Periodic Checks122
Routine Checks123
Cleaning the Filters in the Wash Cabinet123
Cleaning the Spray Arms125
Cleaning the Machine127
Cleaning the Control Panel127
Cleaning the Door and the Door Seal127
Cleaning the Wash Chamber127
Cleaning the Door Front127
Preventing Re-Soiling127
Checking Mobile Units, Baskets, Modules and Inserts128
Changing the HEPA Filter129
Performance Check131
Problem Solving Guide134
Technical Faults and Messages134
Dispensing/Dispensing Systems135
Insufficient Salt/Water Softener136
Cancel with Fault Code137
Process-Related Faults and Messages141
Door143
Unsatisfactory Cleaning and Corrosion143
Spray Arm Monitoring/Conductivity/Wash Pressure145
Water Inlet and Drainage147
Noises148
Printer/Interface148
Problem Solving Guide149
Cleaning the Drain Pump and Non-Return Valve149
Cleaning the Water Intake Filters150
Retrofitting the Large-Surface Filter150
After Sales Service151
Contacting the Customer Service Department151
Software Version152
Installation153
Installation and Levelling153
Building under a Continuous Worktop154
Removing the Lid154
Preventing Heat Build-Up154
Electromagnetic Compatibility (EMC)156
Electrical Connection157
Equipotential Bonding Connection157
Peak-Load Negotiation158
Plumbing159
Connection to the Water Supply159
Retrofitting the Large-Surface Filter160
Connecting the Drain Hose162
Programme Chart163
General Programmes163
Programmes for Specific Soiling164
Programmes for Specific Load Items164
Additional Programmes165
Programme Selection Depending on the Accessories Used165
Mini165
Standard165
Universal165
Intensive165
Injector Plus165
Inorganic165
Organic165
Oil Programme165
Programme Parameters166
Free Memory166
Free Memory167
Special 93°C-10178

Miele PG 8593 - Page 7

Table of Contents

Related product manuals