Mitsubishi Electric FR-F740-00023

166
Frequency setting by analog input (terminal 1, 2, 4)
[,\&150"(9&0(&#9M)-0&($7'&0"5&*+5K)5$,'&C.0"()0&#9M)-0?5$0&(*&#&/#.$&4(70#/5&[,)++5$0\6
[P"5$&,"#$/.$/&0"5&/#.$&*+5K)5$,'&*+(?&^>kV&0(&E>kV\
D$O:Db+
 S"#$/.$/&C4 (Pr. 903)&(+&C7 (Pr. 905)&[/#.$&#9M)-0?5$0\&4#7)5&C.77&$(0&,"#$/5&0"5&Pr. 20&4#7)56&!"5&.$8)0&(*&05+?.$#7&F&[*+5K)5$,'
-500.$/&#)@.7.#+'&.$8)0\&.-&#9959&0(&0"5&-8559&-500.$/&-./$#76
 :(+&0"5&(85+#0.$/&8+(,59)+5&)-.$/&0"5&8#+#?505+&)$.0&[:;<dT>`Y:;<dT>=\B&+5*5+&0(&0"5&:;<dT>`Y:;<dT>=&.$-0+),0.($&?#$)#76
 P"5$&-500.$/&0"5&4#7)5&0(&F]>kV&(+&?(+5B&.0&.-&$5,5--#+'&0(&-50&Pr. 18 High speed maximum frequency&0(&F]>kV&(+&?(+56&(Refer to
page 76)
 1#%5&0"5&2.#-&*+5K)5$,'&-500.$/&)-.$/&calibration parameter C2 (Pr. 902) or C5 (Pr. 904).&(Refer to page 163)
#G:H>5IE
A5&,#)0.()-&C"5$&-500.$/&#$'&4#7)5&(0"5+&0"#$&O>O&#-&0"5&2.#-&*+5K)5$,'&#0&>a&[>?L\6&W45$&.*&#&-8559&,(??#$9&
.-&$(0&/.45$B&?5+57'&0)+$.$/&($&0"5&-0#+0&-./$#7&C.77&-0#+0&0"5&?(0(+&#0&0"5&8+5-50&*+5K)5$,'6
i/<)<B&(&)=#)&@&))&;#(-#i
Pr. 20 Acceleration/deceleration reference frequency Refer to page 90
Pr. 73 Analog input selection, Pr. 267 Terminal 4 input selection Refer to page 155
Pr. 79 Operation mode selection Refer to page 175
Display
Operation
Flicker...Parameter setting complete!!
1. Pr. 125) or
(Pr. 126
)
appears.
4. Press to set.
5. Mode/monitor check
Press twice to choose the
monitor/frequency monitor.
or
Terminal 2 input Terminal 4 input
Terminal 2 input Terminal 4 input
3.
Tu
r
n
t
o c
h
an
g
e t
h
e set va
l
ue to
" ". (60.00Hz)
2. Press to show the present set value.
(50.00Hz)
6. Apply a voltage across the inverter
terminals 2-5 (across 4-5) and turn on the
start command (STF, STR).
Operation starts at 60Hz.