Mitsubishi Electric FR-F740-00023

84
Frequency setting by external terminals
4.6.2 Jog operation (Pr. 15, Pr. 16)
!"5& #2(45& 8#+#?505+-& #+5& 9.-87#'59& #-& -.?875& ?(95& 8#+#?505+-& ($7'& C"5$& 0"5& 8#+#?505+& )$.0& [:;<dT>`Y:;<dT>=\& .-& ,($$5,0596& P"5$& 0"5
(85+#0.($&8#$57&[:;<NT>=\&.-&,($$5,059B&0"5&#2(45&8#+#?505+-&,#$&25&-50&($7'&C"5$&Pr. 160 User group read selection&c&O>O6&(Refer to page 173)
h P"5$&0"5&-500.$/&(*&Pr. 21 Acceleration/deceleration time increments&.-&O>O&[.$.0.#7&4#7)5\B&0"5&-500.$/&+#$/5&.-&O>&0(&_E>>-O&#$9&0"5&-500.$/&.$,+5?5$0-&#+5
O>6F-OB&#$9&C"5$&0"5&-500.$/&.-&OFOB&0"5&-500.$/&+#$/5&.-&O>&0(&_E>-O&#$9&0"5&-500.$/&.$,+5?5$0-&#+5&O>6>F-O
J!K j-L#-?&)<(*-1#@)-B#-7(=*;&
 P"5$& 0"5& M(/& -./$#7& .-& ($B& #& -0#+0& #$9& -0(8& ,#$& 25& ?#95& 2'& 0"5& -0#+0& -./$#7& [b!:B& b!;\6& [!"5& nUR& -./$#7& .-
#--./$59&0(&0"5&05+?.$#7&nUR&.$&0"5&.$.0.#7&-500.$/\
X()&,#$&-50&0"5&*+5K)5$,'&#$9&#,,575 +#0.($Y95,575+#0.($&0.?5&*(+&M(/&(85+#0.($6&n(/&(85+#0.($&,#$&25&85+*(+?59
*+(?&5.0"5+&0"5&()0-.95&(+&dT6
S#$&25&)-59&*(+&,($45'(+&8(-.0.($.$/B&05-0&(85+#0.($B&50,6
/<)<B&(&)#
E7BA&)
E<B&
51*(*<%#
V<%7&
+&((*1L#D<1L& R&=')*?(*-1
!M
#
j-L#@)&Z7&1'8 ^kV >&0(&`>>kV b50&0"5&*+5K)5$,'&*(+&M(/&(85+#0.($6
!N
#
j-L#
<''&%&)<(*-1[
;&'&%&)<(*-1#
(*B&
>6^- >&0(&_E>>Y_E>-h
b50&0"5&#,,575+#0.($Y95,575+#0.($&0.?5&*(+&M(/&(85+#0.($6&L-&0"5&
#,,575+#0.($Y95,575+#0.($&0.?5&-50&0"5&0.?5&0#%5$&0(&+5#,"&0"5&
*+5K)5$,'&-50&.$&Pr. 20 Acceleration/deceleration reference
frequency6&[3$.0.#7&4#7)5&.-&E>kV\
!"5&#,,575+#0.($&#$9&95,575+#0.($&0.?5-&,#$$(0&25&-50&
-58#+#057'6
D$O:Db+
 P"5$&'()&C#$0&0(&,"#$/5&0"5&+)$$.$/&*+5K)5$,'B&,"#$/5&Pr. 15 Jog frequency&6&[.$.0.#7&4#7)5&O^kVO\
 P"5$&'()&C#$0&0(&,"#$/5&0"5&+)$$.$/&*+5K)5$,'B&,"#$/5&Pr. 16 Jog acceleration/deceleration time&6&[.$.0.#7&4#7)5&O>6^O-\
Output
frequency(Hz)
Pr.20
Pr.15
Jog frequency
setting range
Pr.16
Forward
rotation
Reverse
rotation
Time
ON
ON
ON
JOG signal
Forward
rotation STF
Reverse
rotation STR
STF
10
2
5
JOG
Inverter
R/L
1
S/L2
T/L3
U
V
W
Connection diagram for external jog operati
o
STR
Three-phase AC
power supply
Forward rotation start
Reverse rotation start
JOG signal
PC
1.Screen at powering on
Confirm that the External operation mode is selected.
([EXT] lit)
If not displayed, press to change to the
external [EXT] operation mode.
If the operation mode still does not change,
set Pr. 79 to change to the External operation mode.
Indication
Operation
2.Turn the JOG switch on.
ON
Forward
rotation
Forward
rotation
Reverse
rotation
Reverse
rotation
Rotates while ON
Stop
3.Turn the start switch (STF or STR) on.
The motor rotates while start switch
(STF or STR) is ON.
Rotates at 5Hz. (Initial value of Pr. 15)
4.Turn the start switch (STF or STR) off.
ON
OFF