Mitsubishi FX3G Series Programming Manual

821
FX3G/FX3U/FX3GC/FX3UC Series
Programming Manual - Basic & Applied Instruction Edition
37 Operation of Special Devices (M8000 -, D8000 -)
37.1 Special Device List (M8000 -, D8000 -)
31
FNC276-FNC279 Data Transfer 3
32
FNC280-FNC289 High-Speed Processing 2
33
FNC290-FNC299 Extension File Register
34
FNC300-FNC305 FX
3U
-CF-ADP
35
SFC•STL Programming
36
Interrupt Function
37
Special Device
38
Error Code
A
Version Up Information
B
Execution Times
High-Speed Counter Comparison, High-Speed Table, and Positioning [Positioning is supported in FX3G, FX3GC, FX1S, FX1N, and FX1NC
PLCs.]
M 8130
HSZ (FNC 55) instruction:
Table comparison mode
– – 3 3
D8130
––3 – 3
[M]8131
HSZ (FNC 55) instruction:
Table comparison mode completion flag
– – 3 3 ––3 – 3
M 8132
HSZ (FNC 55) and PLSY (FNC 57) instructions:
Speed pattern mode
– – 3 3
D8131 to
D8134
––3 – 3
[M]8133
HSZ (FNC 55) and PLSY (FNC 57) instructions:
Speed pattern mode completion flag
– – 3 3 ––3 – 3
[M]8134
Not used
– – – – – –––– –
[M]8135
– – – – – –––– –
[M]8136
– – – – – –––– –
[M]8137
– – – – – –––– –
[M]8138
HSCT (FNC280) instruction:
Instruction execution complete flag
– – 3 3 D8138–––– –
[M]8139
HSCS (FNC 53), HSCR (FNC 54), HSZ (FNC
55), HSCT (FNC280) instructions:
High-speed counter comparison instruction
executing
– – 3 3 D8139–––– –
M 8140
ZRN (FNC156) instruction:
CLR signal output function enable
– – – ––33 – 3 –
[M]8141
Not used
– – – – – –––– –
[M]8142
– – – – – –––– –
[M]8143
– – – – – –––– –
[M]8144
– – – – – –––– –
M 8145 [Y000] Pulse output stop command
3 3 – ––33 – 3 –
M 8146 [Y001] Pulse output stop command
3 3 – ––33 – 3 –
[M]8147 [Y000] Pulse output monitor (BUSY/READY)
3 3 – ––33 – 3 –
[M]8148 [Y001] Pulse output monitor (BUSY/READY)
3 3 – ––33 – 3 –
[M]8149 Not used
– – – – – –––– –
Inverter Communication Function (Refer to Data Communication Edition for details.)
[M]8150 Not used – – – – – –––– –
[M]8151 Inverter communication in execution [ch1]
3
*3
3 3 3 D8151–––– –
[M]8152
*1
Inverter communication error [ch1]
3
*3
3 3 3 D8152–––– –
[M]8153
*1
Inverter communication error latch [ch1]
3
*3
3 3 3 D8153–––– –
[M]8154
*1
IVBWR (FNC274) instruction error [ch1]
– – 3 3 D8154–––– –
[M]8154 Defined per use of EXTR (FNC180)
– – – ––––
3
*2
–
3
*2
[M]8155 EXTR (FNC180) is using communicating port
– – – – D8155 – –
3
*2
–
3
*2
[M]8156 Inverter communication in execution [ch2]
3
*3
3 3 3 D8156
[M]8156
Communication error or parameter error in
EXTR (FNC180) instruction
– – – – D8156 – –
3
*2
–
3
*2
[M]8157
*1
Inverter communication error [ch2]
3
*3
3 3 3 D8157
Communication error in EXTR (FNC180)
instruction is latched.
– – – – D8157 – –
3
*2
–
3
*2
[M]8158
*1
Inverter communication error latch [ch2]
3
*3
3 3 3 D8158–––– –
[M]8159
*1
IVBWR (FNC274) instruction error [ch2]
– – 3 3 D8159–––– –
*1. Cleared when PLC switches from STOP to RUN.
*2. Available in Ver. 3.00 or later.
*3. Available in Ver. 1.10 or later.
Number and name Operation and function
Applicable model
FX 3G FX 3GC FX3U FX 3UC
Correspond-
ing special
device
FX 1S FX 1N FX 2N FX 1NC FX 2NC

Mitsubishi FX3G Series Specifications

General

Model	FX3G Series
Power Supply	AC 100-240V or DC 24V
Program Capacity	32, 000 steps
Execution Speed	0.21 µs/basic instruction
Communication Options	RS-422, USB, Ethernet
Expansion Modules	Analog, digital, communication
Programming Language	Ladder Logic, Instruction List
Built-in Functions	High-speed counters, pulse output
Analog I/O	Available via expansion modules