mori seiki NL1500/500 User Manual

บ٢ʰʕʍʒ
HYDRAULIC UNIT
100
5) O ʴʽɺȾϾȟȕɟɃ૰Ȭɞǿ 5) If there is any damage to the O-ring, replace it with a new
one.
2 าᜤ 2 NOTE
1. ᯚ٢ӌȺΈႊȪȲکնǾߴȨȽϾȺɕบɕɟȪɑȬǿ 1. Even a tiny scratch will cause an oil leakage if the hydraulic
unit is used under high pressure.
2. ɻ˂ʃႊ O ʴʽɺɁټࣻɂࣷᇋɿ˂ʝʃ᥂ᩌȾȝץȗնɢȮ
ȢȳȨȗǿ
2. For the model No. of the O-ring of the case, contact the Mori
Seiki Service Department.
6) ɻ˂ʃю᥂Ɂ෵ɟɥԚґȾɈȠ՘ɞǿ 6) Wipe any stains off from inside the case.
7) ୿Ȫȗɲʶʫʽʒɥɻ˂ʃȾ՘ɝȤɞǿ 7) Mount the new element on the case.
8) ɻ˂ʃɥ஽᜛஁տȾوᢆȨȮʢʍʓȾ՘ɝȤɞǿ 8) Turn the case clockwise to reinstall it on the head.
፻Ȥʒʵɹᴷ25 ᵻ 35 Nˁm Tightening Torque: 25 – 35 N•m
9) ɻ˂ʃ˩᥂Ɂфᜏ᥂ɥʃʛʔȺ፻ɔɞǿ 9) Tighten the hexagonally-shaped part at the bottom of the
case with a spanner.
11-8 ͽӦบɁํɟȻΈႊኙ
Flow of Hydraulic Oil and Positions where Used
Line Filter
Headstock 1
Chuck
Opening/Closing
Cylinder
Headstock 1 and
Headstock 2 Chuck
Manifold Block
Headstock 1 Brake
Headstock 2 Chuck Opening/Closing Cylinder
Hydraulic Unit
Main Manifold Block
Turret
Headstock 2 Brake
ቼ1˿ᢉʠʶ˂ɷ
ʳɮʽʟɭʵʉ
บ٢ʰʕʍʒ
ʫɮʽʨʕʥ˂ʵʓʠʷʍɹ
ቼᴯ˿ᢉʋʭʍɹᩒᩐႊʁʴʽʊ
ቼᴯ˿ᢉʠʶ˂ɷ
ҏ࿎ի
ቼ1Ǿቼᴯ˿ᢉʋʭʍɹᩒ
ᩐႊʨʕʥ˂ʵʓʠʷʍɹ
ቼ1˿ᢉʋʭʍɹ
ᩒᩐႊʁʴʽʊ

mori seiki NL1500/500 Specifications

General

Brand	mori seiki
Model	NL1500/500
Category	Lathe
Language	English