mori seiki NL1500/500 User Manual

43
ൡಽ଩ͽ
MACHINE OPERATION
14.ʚ˂ʟɭ˂ʊɗ˿ᢉ៩ᣮሰɥΈႊȬɞȻȠɂǾɑȶȬȣȽ
ʚ˂యɥΈႊȪȹȢȳȨȗǿɑȲǾ˿ᢉᴥʓʷ˂ʛɮʡᴦ
юɛɝߴȨȗɁʚ˂యɥӏࡾȬɞȻȠɂǾɶɮʓʠʍ
ʁʯȽȼɥΈႊȪȹȢȳȨȗǿ
ᵘൡಽɁળӦǾӏࡾጀ࣊Ⱦমᬭᵚ
14.When machining bar stock on a machine equipped with
a bar feeder or spindle through-hole, use straight bar
stock only. When machining bar stock with a diameter
smaller than that of the spindle (or draw pipe), use a
guide bush.
[Machine vibration/Impaired machine accuracy]
15.ᒲӦᤆᢆ˹ɂǾʋʍʡɽʽʣʮɥࢠ஽ᤆᢆȨȮȹȢȳȨ
ȗǿ
ᵘҒɝȢȭɁڝሥȾɛɞʋʍʡɽʽʣʮɁᆍૺᵚ
15.Keep the chip conveyor operating all the times during
automatic operation.
[Chip accumulation causing chip conveyor damage]
16.ʙ˂ʓɴ˂ʚʒʳʣʵൡᑤȟᚽ϶ȨɟȹȗɞൡಽȺʙ˂ʓ
ɴ˂ʚʒʳʣʵɥᜓ᪍ȬɞȻȠǾȐቼ 2 O.T. ᜓ᪍ȑʦʉʽ
ɥઃȬȻǾᢉሉӦȾᩜȬɞɮʽʉʷʍɹɂᜓ᪍ȨɟɑȬǿ
ፏߦȾʙ˂ʓɴ˂ʚʒʳʣʵȪȲ஁տȾɂᢉሉӦȪȽȗȺ
ȢȳȨȗǿɑȲǾާпɁȲɔʙ˂ʓɴ˂ʚʒʳʣʵ࿡ৰȟ
ᜓ᪍ȨɟɞɑȺǾʙʽʓʵᣞɝ଩ͽ
V
Ȑu1ȑȺᢉሉӦɥ
ᚐȶȹȢȳȨȗǿ
ᵘիȻɵʚ˂ȟࢱຒᵚ
16.When releasing the hard overtravel on a machine with
that function, the axis movement interlock can be
released by pressing the [2nd O.T. Release] button. Do
not move the axis in the direction in which the hard
overtravel occurred. For safety reasons, feed the axes
using the handle feed
V
[u1] until the hard overtravel
status has been canceled.
[Interference between carriage and covers]
17.ʹ˂ɹɥધȝɛɆୈધȬɞȻȠɂǾʹ˂ɹᒲͶɁҴɥ
ᐎȪȹǾʹ˂ɹȟɅȭɑȽȗɛșȾǾધ஁ศǾୈધ஁
ศǾʋʭʍɹ٢ȝɛɆઃᢉ૜ӌᴥઃറᴦɥ೫᜞Ȫȹ
ȢȳȨȗǿ
ᵘӏࡾጀ࣊ɋɁমᬭᵚ
17.When chucking or supporting a workpiece, take the
rigidity of the workpiece into account when
determining the chucking or supporting method and
chucking pressure or tailstock thrust (if installed).
[Impaired machine accuracy]
ᴹʉʍʋʛʗʵᴻ <Touch Panel>
1. ʉʍʋʛʗʵɂϾȷȠɗȬȗɁȺǾȭ઩Ⱥ᜔ɟȹ଩ͽȪ
ȹȢȳȨȗǿʉʍʋʤʽɥࠖȪȹȗɞൡಽȺɂǾʉʍʋ
ʤʽɥΈႊȪȹȢȳȨȗǿ
1. Use a finger to touch the panel as it can be easily
scratched. Use a touch-pen if one is supplied with the
machine.
2. ʦ˂ʵʤʽȽȼаብɁِȗɕɁɗ᧛ҟȽɕɁǾɑȲྲɁа
Ⱥ଩ͽȪȽȗȺȢȳȨȗǿ
2. Do not touch the panel with anything with a solid tip,
such as a ballpoint pen, anything sharp, or a fingernail.
3. պ஽Ⱦ 2 ኙ˨Ɂɷ˂ɥઃȨȽȗȺȢȳȨȗǿ
ᵘൡಽɁఙȮȿӦͽȾɛɞൡಽɁᆍૺᵚ
3. Do not press more than one key at the same time.
[Machine damage by unexpected machine operation]
4. ࢍ៧Ɂ๬௕ί឴ʟɭʵʪɂΈႊȪȽȗȺȢȳȨȗǿ
ᵘʉʍʋʛʗʵɁ᝝ͽӦᵚ
4. Do not use commercially available liquid crystal
protective film.
[Improper operation of touch panel]
5. ᚨɥᅔႊȪȹ଩ͽȪȽȗȺȢȳȨȗǿ
ᵘʉʍʋʛʗʵɁϾȷȠǾ᝝ͽӦᵚ
5. Do not touch the panel while wearing gloves.
[Improper operation of touch panel, scratches]
6. ʉʍʋʛʗʵɁ᚜ᬂɁ෵ɟȽȼɥઝȠ՘ɞکնɂǾࢍ៧Ɂ
ɹʴ˂ʕʽɺɹʷʃɥΈȗǾྲɥ቏ȹȭȾ઩ɁᒆȺᢌȢઝ
ȗȹȢȳȨȗǿ
6. If the touch panel is smudged, wipe the smudging off
gently with a commercially available cleaning cloth
using the ball of a finger; not a fingernail.
7. ɬʵɽ˂ʵɥֆɦȳɹʴ˂ʕʽɺ๬ɂΈႊȪȽȗȺȢȳȨ
ȗǿ
ᵘʉʍʋʛʗʵɁӐԇǾ୒᪩ᵚ
7. Do not use cleaning fluid containing alcohol.
[Deterioration of touch panel, malfunction]
7-1 ʡʷɺʳʩʽɺ
Programming
8 ឬ֖ 8 WARNING
1. ᜤᢐȪȹȗɞʡʷɺʳʪ΍ɂǾȬɌȹɁൡಽȾߦȪȹȗ
ɞɢȤȺɂȕɝɑȮɦǿȝ޵റȟ᠔оȨɟȲൡಽɁᑤӌɥ
Ԛґ૱ȪȲ˨ȺǾఊᤛȽʡʷɺʳʪɥͽȪǾާпɥᐎ
ȪȹӏࡾɥᚐȶȹȢȳȨȗǿൡಽɁᑤӌɥԚґ૱Ȯȭ
ȾʡʷɺʳʪɥͽȪǾӏࡾɥᚐșȻǾʹ˂ɹɗҒҭࡾщ
ȟ᭣ɆҋȬȝȰɟȟȕɝɑȬǿ
1. The programs given in this manual are not applicable
to all types of machines. Programs must be written
while taking the performance of the machine into
consideration and be executed with due consideration
given to safety. If the machine's capacity is not taken
into account when writing the program, the workpiece
or cutting tool may fly out during machining.
2. ʡʷɺʳʪоӌጶɂǾʛʗʵ଩ͽᤣɷ˂ʃɮʍʋɥ
i
Ȑ଩ͽժȑɑȲɂ
u
Ȑ଩ͽ˪ժȑɁͱᏚȾȪǾʡʷ
ɺʳʪȟ˪ႊ৙Ⱦ፾󰩠ȨɟȽȗɛșȾȪȹȢȳȨȗǿ
ᵘൡಽɁఙȮȿӦͽᵚ
2. Place the operation selection key-switch in the
i
[ON]
or
u
[OFF] position after completing program entry to
prevent the program being accidentally updated.
[Unexpected machine motion]

mori seiki NL1500/500 Specifications

General

Brand	mori seiki
Model	NL1500/500
Category	Lathe
Language	English