mori seiki NL1500/500 User Manual

˿ᢉɁৼɜȪᤆᢆ
SPINDLE WARM-UP
82
ᴹʡʷɺʳʪ΍ᴻ <Program example>
ஓΈႊȬɞӏࡾʡʷɺʳʪɁఊᯚوᢆᣱ࣊ɥ 2000 min
1
Ȼ
ȪȲکնɁʡʷɺʳʪɥ˩ᜤȾᇉȪɑȬǿ
The warm-up program shown below is for cases where the
maximum rotation speed for the machining programs of the
day is 2000 min
1
.
9-2 ᩋఙᩖϦඨɁৼɜȪᤆᢆ
Spindle Warm-Up after Extended Idle Period
ൡಽɥ 2 ᣸ᩖ˨ϦඨȪȲǾѓ࣊ൡಽɥᤆᢆȬɞȻȠɂǾ
˩᚜ȾȶȹৼɜȪᤆᢆɥᚐȶȹȢȳȨȗǿوᢆࡾщ˿ᢉɁ
کնɕպറȾৼɜȪᤆᢆɥᚐȶȹȢȳȨȗǿᴥʩ˂ʴʽɺ
റᴦ
Perform the spindle warm-up before restarting the machine
after an idle period of two weeks or more, referring to the table
below. Perform the spindle warm-up by the same procedure for
rotary tool-spindle. (Milling specifications):
2 าᜤ 2 NOTE
ࢠႊఊᯚوᢆᣱ࣊ɥژໄȾȪȹᚐȶȹȢȳȨȗǿ᚜юɁ % ɂࢠႊఊ
ᯚوᢆᣱ࣊ȾߦȬɞ෗လɥ᚜ȪɑȬǿ
Adjust the rotation speed for warm-up based on the regularly used
maximum rotation speed. The percentage in the table below indicates
the ratio to the regularly used maximum rotation speed.
O0001;
G97 S100 M03;
G04 X600.0;
S500;
G04 X600.0;
S1000;
G04 X300.0;
S1500;
G04 X300.0;
S2000;
G04 X300.0;
M05;
M30;
O0001;
M45;
G97 S100 M13;
G04 X600.0;
S500;
G04 X600.0;
S1000;
G04 X300.0;
S1500;
G04 X300.0
S2000;
G04 X300.0;
M05;
M46;
M30;
<For Spindle> <For Rotary Tool-Spindle>
ᴹ˿ᢉႊᴻ
ᴹوᢆࡾщ˿ᢉႊᴻ
෉᪡
Step
ৼɜȪᤆᢆᣱ࣊
Warm-Up Speed
஽ᩖ
Time
15 %
60 ґ
60 minutes
2 25 %
15 ґ
15 minutes
3 50 %
10 ґ
10 minutes
4 75 %
10 ґ
10 minutes
5 100 %
60 ґ
60 minutes

mori seiki NL1500/500 Specifications

General

Brand	mori seiki
Model	NL1500/500
Category	Lathe
Language	English