MTX MTX-3G-JAVA-IoT - 1.7.3 Power Consumption

MTX-xG-JAVA-IoT Family
www.mtxm2m.com 2017/07 v1.2 Page 24/105
MTX M2M® by MATRIX ELECTRONICA S.L.U
1.7.3 Power Consumption
It is recommend to use 12V/1.5A power supply.
Description
Conditions
Typical
Unit
IIN
1
ULP mode supply
current
Ultra Low Power Mode
2.5
µA
Sleep mode supply
current
Internal GSM module powered down
7
mA
Average
GSM/GPRS supply
current
IDLE (UART activated but no
communication) @ DRX=2
USB disconnected
11
mA
USB active
12
mA
GPRS Data transfer
GSM850/900; PCL=5; 1Tx/4Rx
ROPR=4 (max. reduction)
67
mA
ROPR=0 (no reduction)
GPRS Data transfer
GSM850/900; PCL=5; 2Tx/3Rx
ROPR=4 (max. reduction)
84.5
mA
ROPR=0 (no reduction)
115
mA
GPRS Data transfer
GSM850/900; PCL=5; 4Tx/1Rx
ROPR=4 (max. reduction)
90
mA
ROPR=0 (no reduction)
205
mA
EDGE Data transfer
GSM850/900; PCL=5; 1Tx/4Rx
ROPR=4 (max. reduction)
50
mA
ROPR=0 (no reduction)
EDGE Data transfer
GSM850/900; PCL=5; 2Tx/3Rx
ROPR=4 (max. reduction)
64.5
mA
ROPR=0 (no reduction)
81
mA
EDGE Data transfer
GSM850/900; PCL=5; 4Tx/1Rx
ROPR=4 (max. reduction)
97
mA
ROPR=0 (no reduction)
136
mA
GPRS Data transfer
GSM1800/1900; PCL=0; 1Tx/4Rx
ROPR=4 (max. reduction)
52
mA
ROPR=0 (no reduction)
GPRS Data transfer
GSM1800/1900; PCL=0; 2Tx/3Rx
ROPR=4 (max. reduction)
57
mA
ROPR=0 (no reduction)
85
mA
GPRS Data transfer
GSM1800/1900; PCL=0; 4Tx/1Rx
ROPR=4 (max. reduction)
67
mA
ROPR=0 (no reduction)
145
mA
EDGE Data transfer
GSM1800/1900; PCL=0; 1Tx/4Rx
ROPR=4 (max. reduction)
45
mA
ROPR=0 (no reduction)
EDGE Data transfer
GSM1800/1900; PCL=0; 2Tx/3Rx
ROPR=4 (max. reduction)
62
mA
ROPR=0 (no reduction)
70
mA
EDGE Data transfer
GSM1800/1900; PCL=0; 4Tx/1Rx
ROPR=4 (max. reduction)
95
mA
ROPR=0 (no reduction)
115
mA
Average WCDMA
supply current
supply current
IDLE (UART activated but no
communication) @ DRX=6
USB disconnected
10
mA
USB active
16
mA
UMTS Data transfer Band I @ 23dBm
132
mA
UMTS Data transfer Band II @ 23dBm
150
mA
UMTS Data transfer Band V/VI @ 23dBm
150
mA
UMTS Data transfer Band VIII @ 23dBm
152
mA
HSPA Data transfer Band I @ 23dBm
132
mA
HSPA Data transfer Band II @ 23dBm
150
mA
HSPA Data transfer Band V/VI @ 23dBm
150
mA
HSPA Data transfer Band VIII @ 23dBm
152
mA
1. With an impedance of Z
LOAD
=50Ohm at the antenna port.
2. Measurements start 6 minutes after switching ON the modules
Average times: SLEEP and ULP mode – 3 minutes, transfer modes – 1.5 minutes
Communication tester settings: no neighbor cells, no cell reselection etc., RMC (reference measurement channel)
Description
Conditions
Typ
Max
Unit
ULP mode supply
current
T
A
= 25ºC
2.5
5
µA
T
A
= 85ºC
8.5
34
µA