NEC ASPILA EX - Securing the Main Cabinet to the Wall (Figure 1-8

To Next Page

To Previous Page

Section 1: Installing the Cabinets

1-10 Section 1: Installing the Cabinets Aspila EX Hardware

Securing the Main Cabinet to the Wall (Figure 1-8 - Figure 1-12)

1. Install the wall bracket to the wall providing the appropriate spacing as shown below. The two

top key-hole screws should protrude from the wall about 3mm to allow the bracket to slide

over the screw heads.

It is suggested that plywood first be installed on the wall where the cabinet will be posi-

tioned. This allows for secure anchoring of the screws which will be supporting the weight of

the cabinet.

Note: Only one cabinet should be wall mounted. Two cabinets may result in too much

weight to be safely mounted together. The weight of a two cabinet system can be up to 50kg.

Figure 1-8: INSTALLING THE MOUNTING BRACKET

CÔNG TY VIỄN THÔNG VIỆT PRO

Chuyên phân phối tổng đài NEC

http://vietpro.com.vn

Main Page

Table of Contents3
Installing the Main and Expansion Cabinets17
Parts8
Installing the Main Cabinet19
- Removing the Front Cover (Figure 1-1)110
- Removing the Side Panels (Figure 1-2)111
- Using12
- Securing the Main Cabinet to the Wall (Figure 1-8 - Figure 1-12)116
- Securing the Main Cabinet to a Rack (Figure 1-13 - Figure 1-17)119
Installing an Expansion Cabinet124
- Power Supplies in the Main and Expansion Cabinets137
Grounding the Cabinets138
Completing the Installation140
Pcb Layout243
- Order of Installing Extension Pcbs244
Pcb Installation245
- Removing an Extension or Trunk PCB246
- Where to Install the Pcbs247
- Central Processing Unit (NTCPU) PCB (Figure 2-3)248
- Connector Pin-Outs on NTCPU252
- Expansion (EXIFU) PCB (Figure 2-5)256
- DSPDB Daughter Board (Figure 2-6, Figure 2-7)257
- Digital Station (8/16ESIU) PCB (Figure 2-8)259
- Analogue Station (8SLIU) PCB (Figure 2-9)261
- Analogue Station (8SLIDB) Daughter Board (Figure 2-10 - Figure 2-11)263
- Analogue Trunk (4/8COIU) PCB (Figure 2-12)265
- Direct Inward Dial (DID) (4/8DIOPU) PCB (Figure 2-13)268
- Tie Line (4TLIU) PCB (Figure 2-14)270
- BRI (2/4/8BRIU) Interface PCB (Figure 2-15)276
- PRI (1PRIU) Interface PCB (Figure 2-16)279
- In-Skin Server/Router (APSU) PCB (Figure 2-17)282
- LAN 8-Port Switching Hub (8SHUBU) PCB (Figure 2-18)285
- Voip (16VOIPU) PCB (Figure 2-19)287
- Voip (VOIPDB) Daughter Board (Figure 2-20 - Figure 2-21)288
Pcb Startup290
- Initial Installation of Trunk Pcbs291
System Startup292
- Initial Programming (Figure 2-22)293
- Setting up Extension Circuit Types294
- Making Test Calls295
- Basic Troubleshooting296
- Identifying Port Location297
System Shutdown298
Rj61 Wiring and Pinouts3100
Specifications and Parts101
Installing Single Line Telephones3102
Installing Co/Pbx Lines3103
Installing Bri Trunks3104
Installing Pri Trunks3105
Installing DID Trunks3106
Installing Tie Lines3107
Testing Telephone Operation3109
Super Display Lcd3110
Pgdad Module4111
- LED Indications4112
Background Music4116
Door Box4117
Dss Console4120
External Paging4123
External Paging and Page Relays4125
Headsets4126
System Phone Labeling4127
Music Sources4128
Night Mode Selection4130
Optional Phone Adapters4131
Removing the Adapter Cover (Figure 4-19)4132
ADA Adapter (Figure 4-20 - Figure 4-26)4133
APA and APR Adapters (Figure 4-27 - Figure 4-28)4136
CTA Adapter (Figure 4-27 - Figure 4-28)4138
CTU Adapter (Figure 4-31 - Figure 4-32)4139
Voip Adapter (Figure 4-33 - Figure 4-35)4140
Power Failure Telephones4142
Slt Adapter4144
Telephone Legs4146
Wall-Mount Bracket4149
- Wall-Mounting the Phone (Figure 4-50 - Figure 4-50)4150
- Data Communications5157
- Data Communication Availability with Hardware5158
- Ports for APR Adapter5159
Smdr5160
- Programming SMDR5161
Lan Devices6163
- Subnet Mask164
- Installing a LAN Device or Voip168

NEC ASPILA EX - Securing the Main Cabinet to the Wall (Figure 1-8 - Figure 1-12)1

Table of Contents

Other manuals for NEC ASPILA EX

Related product manuals