NETGEAR GS110TUP User Manual

PoE++ overview
The PoE++ ports on model GS110TUP (port 1–4) and model GS710TUP (port 1–8)
support IEEE 802.3bt Type 3 with 4-pair PoE. These models are also compatible with
PoE+ (IEEE 802.3at) and PoE (IEEE 802.3af) and can support non-PoE devices.
The maximum PoE power budget on the switch depends on the model:
•
Model GS110TUP. The maximum PoE power budget across all active PoE++ and
PoE+ ports is 240W.
The maximum PoE power that an individual PoE++ port can supply is 60W.
The maximum PoE power that an individual PoE+ port can supply is 30W.
•
Model GS710TUP. The maximum PoE power budget across all active PoE++ ports
is 480W.
The maximum PoE power that an individual PoE++ port can supply is 60W.
The PoE++ and PoE+ power supplied by the switch is prioritized in ascending port
order (from port 1 to port 8), with a total power budget of 240W (model GS110TUP) or
480W (model GS710TUP) across all active PoE++ and PoE+ ports.
The following table shows the standard power ranges, calculated with the maximum
cable length of 328 feet (100 meters). If a device receives insufficient PoE power from
the switch, consider using a shorter cable.
Table 4. PoE classes and PoE power allocations
Power Delivered to the
Device
Maximum Power
Supplied by the Switch
Class DescriptionCompatible PoE
Standard
Device
Class
0.44W–13.0W15.4WDefault power (full)PoE, PoE+, and PoE++0
0.44W–3.84W4.0WVery low powerPoE, PoE+, and PoE++1
3.84W–6.49W7.0WLow powerPoE, PoE+, and PoE++2
6.49W–13.0W15.4WMid powerPoE, PoE+, and PoE++3
13.0W–25.5W30.0WHigh powerPoE+ and PoE++4
25.5W–40.0W45.0WUltra high powerPoE++5
40.05W–51.0W60.0WUltra high powerPoE++6–8
The switch supports uninterrupted PoE, which enables the switch to provide PoE power
while rebooting. By default, the uninterrupted PoE feature is disabled, causing the switch
to stop providing PoE power while it is rebooting. If you enable the uninterrupted PoE
feature, the switch continues to provide PoE power to any attached PDs while the switch
is rebooting, even if it is rebooting after a regular firmware update.
Hardware Installation Guide21Applications
10-Port Gigabit Ethernet Ultra60 PoE++ Smart Managed Pro Desktop and Rackmount Switches

NETGEAR GS110TUP Specifications

General

Switch type	Managed
Switch layer	L2/L3
Power connector	DC-in jack
SFP module slots quantity	1
Installed SFP modules quantity	-
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	10
Product color	White
Rack mounting	Yes
LED indicators	Activity, Link, PoE, Power, Speed
Number of fans	0 fan(s)
Heat dissipation	945 BTU/h
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	0 - 95 %
Total Power over Ethernet (PoE) budget	240 W
Power over Ethernet plus (PoE+) ports quantity	8
Input current	4.7 A
DC input voltage	54 V
Power consumption (max)	276.8 W
Package type	Gift box
Master (outer) case width	402 mm
Master (outer) case height	357 mm
Master (outer) case length	453 mm
Master (outer) case weight	20140 g
Harmonized System (HS) code	85176990
Quantity per master (outer) case	6 pc(s)
Jumbo frames	10000
Forwarding rate	14.8 Mpps
MAC address table	8000 entries
Packet buffer memory	0.512 MB
DHCP features	DHCP client, DHCP snooping
Security algorithms	SSL/TLS
Queue scheduling algorithms	Weighted Round Robin (WRR)
Access Control List (ACL) IPv6 entries	100
10G support	No
Number of VLANs	64
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3ad, IEEE 802.3x
Number of multicast groups filtered	256
Noise level	0 dB
Mean time between failures (MTBF)	695508 h

Weight and Dimensions

Depth	101 mm
Width	236 mm
Height	27 mm
Weight	630 g