EasyManuals Logo

NETGEAR MS108EUP Hardware Installation Guide

NETGEAR MS108EUP
30 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #7 background imageLoading...
Page #7 background image
-
IEEE 802.3x Full-duplex flow control
- IEEE 802.1Q VLAN tagging
- IEEE 802.3ad Link aggregation (LAG with LACP)
-
IEEE 802.1p Class of Service (QoS)
-
IEEE 802.3az Energy Efficient Ethernet (EEE)
-
IEEE 802.1af (PoE)
- IEEE 802.1at (PoE+)
- IEEE 802.1bt (PoE++)
AutoSensing and autonegotiating capabilities for all ports.
Auto Uplink™ technology is supported on all ports.
Automatic address learning function to build the packet-forwarding information
table. The table contains up to 16K Media Access Control (MAC) addresses.
Store-and-forward transmission to remove bad packets from the network.
Active flow control to minimize packet loss and frame drops.
Per-port status LEDs and system status LEDs.
NETGEAR green power-saving features:
-
Energy efficiency mode that fully conforms to the IEEE802.3az standard
- Per-port automatic change to a lower power mode when the port link is down
Safety instructions and warnings
Use the following safety guidelines to ensure your own personal safety and to help
protect your system from potential damage.
To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,
observe the following precautions:
This product is designed for indoor use only in a temperature-controlled and
humidity-controlled environment.
Note the following:
-
For more information about the environment in which this product must operate,
see the environmental specifications in the appendix or the data sheet.
-
If you want to connect the product to a device located outdoors, the outdoor
device must be properly grounded and surge protected, and you must install an
Hardware Installation Guide7Introduction
8-port Ultra60 PoE++ Multi-Gigabit (2.5G) Ethernet Plus Switch MS108EUP

Other manuals for NETGEAR MS108EUP

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR MS108EUP and is the answer not in the manual?

NETGEAR MS108EUP Specifications

General IconGeneral
Switch typeManaged
Switch layerL2/L3
Quality of Service (QoS) supportYes
Installed SFP modules quantity-
Basic switching RJ-45 Ethernet ports type2.5G Ethernet (100/1000/2500)
Basic switching RJ-45 Ethernet ports quantity8
10G supportNo
Number of VLANs64
Networking standardsIEEE 802.1Q, IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3af, IEEE 802.3at, IEEE 802.3az, IEEE 802.3bt, IEEE 802.3u, IEEE 802.3x
Virtual LAN featuresPort-based VLAN, Tagged VLAN
Copper ethernet cabling technology100BASE-T, 1000BASE-T
Jumbo frames12000
MAC address table16000 entries
Packet buffer memory1.5 MB
DHCP featuresDHCP client
Queue scheduling algorithmsStrict Priority Queue (SPQ), Weighted Round Robin (WRR)
Number of multicast groups filtered128
Operating altitude0 - 3000 m
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 40 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)0 - 90 %
Total Power over Ethernet (PoE) budget230 W
Power sourcePoE
Mean time between failures (MTBF)373644 h
CertificationCE FCC 15 B CE/EN55032/24 CSA VCCI ACMA KC CCC BSMI
Product colorGray
Housing materialMetal
Weight and Dimensions IconWeight and Dimensions
Depth140 mm
Width210 mm
Height40 mm
Weight900 g

Related product manuals