EasyManuals Logo

NETGEAR WGR614 User Manual

NETGEAR WGR614
146 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #119 background imageLoading...
Page #119 background image
Reference Manual for Cable/DSL Wireless Router WGR614
Preparing Your Network C-19
An IP address and subnet mask
A gateway IP address, which is the address of the ISP’s router
One or more domain name server (DNS) IP addresses
Host name and domain suffix
For example, your account’s full server names may look like this:
mail.xxx.yyy.com
In this example, the domain suffix is xxx.yyy.com.
If any of these items are dynamically supplied by the ISP, your firewall automatically acquires
them.
If an ISP technician configured your PC during the installation of the broadband modem, or if you
configured it using instructions provided by your ISP, you need to copy the configuration
information from your PC’s Network TCP/IP Properties window or Macintosh TCP/IP Control
Panel before reconfiguring your PC for use with the firewall. These procedures are described next.
Obtaining ISP Configuration Information for Windows Computers
As mentioned above, you may need to collect configuration information from your PC so that you
can use this information when you configure the WGR614 router. Following this procedure is only
necessary when your ISP does not dynamically supply the account information.
To get the information you need to configure the firewall for Internet access:
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network icon.
The Network window opens, which displays a list of installed components.
3. Select TCP/IP, and then click Properties.
The TCP/IP Properties dialog box opens.
4. Select the IP Address tab.
If an IP address and subnet mask are shown, write down the information. If an address is
present, your account uses a fixed (static) IP address. If no address is present, your account
uses a dynamically-assigned IP address. Click “Obtain an IP address automatically”.
5. Select the Gateway tab.

Table of Contents

Other manuals for NETGEAR WGR614

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR WGR614 and is the answer not in the manual?

NETGEAR WGR614 Specifications

Power IconPower
power adapter voltage12 VDC
Interface and Networking IconInterface and Networking
internet WAN10/100 Mbps (auto-sensing) Ethernet, RJ-45
LAN ports4 ports 10/100 Mbps (auto-sensing) Ethernet, RJ-45
wireless network speeds1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, & 54 Mbps (auto-rate capable)
Wireless Specifications IconWireless Specifications
modulation typeOFDM with BPSK, QPSK, 16QAM, 64QAM, DBPSK, DQPSK, CCK
frequency range US2.412 ~ 2.462 GHz
frequency range Japan2.412 ~ 2.484 GHz
frequency range Europe ETSI2.412 ~ 2.472 GHz
frequency range Spain2.457 ~ 2.462 GHz
frequency range France2.457 ~ 2.472 GHz
Security IconSecurity
encryption40-bit (also called 64-bit), 128-bit, and 152-bit (802.11g only) WEP encryption, WPA (Wi-Fi Protected Access)
firewallStateful Packet Inspection (SPI), DoS Attack Detection/Logging, Dropped Packet Log, Security Event Log, E-mail Log
Weight and Dimensions IconWeight and Dimensions
dimensions6.9 x 1.1 x 4.7 in (175.3 x 27.94 x 119.4 mm)
weight0.3 kg (0.7 lb)
antenna gain2 dBi

Related product manuals