To Next PageTo Next PageWhat to do if my Nilfisk-Advance Blower does not move?
If your Nilfisk-Advance Blower isn't moving, there are several potential causes: * The battery might be disconnected. If this is the case, connect the battery. * The machine may be out of fuel, so refuel it. * Check if the fuses are tripped and reset any that are. * The parking brake could be engaged; disengage it. * Ensure the unlocking screw is properly positioned by turning it correctly.
Why is my Nilfisk-Advance Blower collecting little debris/dust?
If your Nilfisk-Advance Blower is not effectively collecting debris or dust, consider these possibilities: * The vacuum system may be off. Turn it on using the switch. * The dust filter could be clogged, so clean it. * The hopper might be full; empty it. * The skirts may be damaged or misadjusted; check their integrity and adjustment. * The main broom height might be incorrect; adjust it. * A fuse might be tripped; reset any tripped fuse.
What to do if the main broom does not turn on my Nilfisk-Advance Blower?
If the main broom on your Nilfisk-Advance Blower isn't turning, it might be due to a few reasons: * The main broom could be lifted. Lower it using the lever. * There might be debris wrapped around the broom drive, so remove any debris. * The hopper may not be fully lowered; fully lower the hopper.
Why is the side broom not working on my Nilfisk-Advance Blower?
If the side broom on your Nilfisk-Advance Blower isn't working, consider these potential issues: * The side broom might be lifted. Lower it using the lever. * Debris could be wrapped around the broom drive; remove any debris. * The hopper might not be fully lowered; fully lower the hopper.
What causes the filter shaker motor to not work on a Nilfisk-Advance Blower?
If the filter shaker motor on your Nilfisk-Advance Blower isn't working, check these: * The filter shaker motor connector may not be properly connected; connect it properly. * A fuse might be tripped; reset the tripped fuse.
What to do if the hopper dumping door does not close on my Nilfisk-Advance Blower?
If the hopper dumping door on your Nilfisk-Advance Blower doesn't close, it's likely because the dumping door is jammed by debris. Remove the debris and clean the edges of the dirt chamber.
Why is the dust guard system (optional) not working on my Nilfisk-Advance Blower?
If the dust guard system on your Nilfisk-Advance Blower isn't working, check the following: * The switch may be faulty, consider replacing the switch. * The nozzles or the water filter may be clogged; clean them. * The pump may be faulty; replace it. * A fuse might be tripped; reset the tripped fuse.
General| Brand | Nilfisk-Advance |
|---|---|
| Model | SR 1601 D3 |
| Category | Floor Machine |
| Language | English |
Explains warning symbols displayed directly on the machine for safe operation.
Details the dangers of CO from the engine and necessary ventilation precautions.
Steps to take before performing maintenance, repair, or cleaning.
Key safety rules for operating the machine, including inclines and clothing.
Precautions for refueling, including fire prevention and skin contact.
Details the function of various levers, switches, and indicators on the control panel.
Explains the ignition key positions and the purpose of warning lights.
Essential checks to perform before starting the machine for operation.
Final checks and preparations before engine start-up.
Step-by-step instructions for safely starting the machine's engine.
Procedures for safely shutting down the machine.
Instructions for lowering brooms, activating vacuum, and dust guard systems.
Guidance on driving, overlap, and using the filter shaker during sweeping.
Steps for safely emptying the hopper, including safety support use.
Table outlining maintenance tasks and their recommended intervals based on operating hours.
Instructions for replacing worn main broom bristles, including safety precautions.
Procedure for adjusting the main broom height for optimal cleaning performance.
How to adjust the side broom pressure and height for effective sweeping.
Procedures for cleaning or replacing the panel-type dust filter.
Solutions for issues related to the machine not moving or brooms not turning.
Troubleshooting for poor debris collection, side broom operation, and hopper door problems.
