NTI ENVIROMUX TEMPERATURE/HUMIDITY SENSOR ATTACHMENT
15
TEMPERATURE AND HUMIDITY SENSORS
SENSOR MODEL OPERATING TEMPERATURE
RANGE
HUMIDITY RANGE ACCURACY
E-STS 32 to 122°F (0 to 50°C) n/a ±0.9°F (±0.5°C)
E-STS-O / E-STS-IP67 -40°F to 185°F (-40°C to +85°C) n/a ±0.9°F (±0.5°C)
E-STSM-E7 -4 to 140°F (-20 to 60°C) n/a
±1.26°F (±0.70°C) for -4 to
41°F (-20 to 5°C)
±0.72°F (±0.40°C) for 41 to
140°F (5 to 60°C)
E-STHS-LSH -4 to 140°F (-20 to 60°C) 0 to 90% RH
±.90°F (±0.50°C) for -4 to
14°F (-20 to -10°C)
±0.72°F (±0.40°C) for 14 to
140°F (-10 to 60°C)
Inflation due to self-heating
<0.9°F (0.5°C) typical, 2.3°F
(1.3°C) max.
10 to 80% RH, ±3%(30°C)
80 to 90% RH, ±4%(30°C)
E-STHSB
-4 to 185°F (-20 to 85°C)
0 to 80% RH,
±3%(30°C)
80 to 90% RH,
±4%(30°C)
±.90°F (±0.50°C) for -4 to
14°F (-20 to -10°C)
±0.72°F (±0.40°C) for 14 to
185°F (-10 to 85°C)
E-STHSM-E7 -4 to 140°F (-20 to 60°C) 0 to 90% RH
±.90°F (±0.50°C) for -4 to
14°F (-20 to -10°C)
±0.72°F (±0.40°C) for 14 to
140°F (-10 to 60°C)
10 to 80% RH, ±3%(30°C)
80 to 90% RH, ±4%(30°C)
E-STHS-LCD(W) -4 to 140°F (-20 to 60°C) 0 to 90% RH
±.90°F (±0.50°C) for -4 to
14°F (-20 to -10°C)
±0.72°F (±0.40°C) for 14 to
140°F (-10 to 60°C)
10 to 80% RH, ±3%(30°C)
80 to 90% RH, ±4%(30°C)
E-STHS-PRC 32 to 140°F (0 to 60°C) 10% to 80% RH ± 0.4°F(±0.2°C)
± 1.8%RH@86°F (30°C)
E-STSP
E-STSP-SL-7
-40 to 185°F (-40 to 85°C) n/a ±1.0°F (±0.5°C).
Sensor Calibration
All temperature/humidity combination sensors and humidity-only sensors are designed to be accurate within the specifications
stated in the chart above. They are not designed to be re-calibrated. In the event you want the calibration of your sensor to be
checked, please contact NTI for an RMA to return your sensor. Sensor accuracy will be checked for a nominal charge. Sensors
within warranty that are found to be out of factory specification will be repaired or replaced at no additional charge. Normal labor
or replacement charges will apply to sensors out of warranty and out of specification.
Power Consumption
All of our temperature and temperature/humidity sensors operate at 5VDC and draw between 10-56mA (the highest being the E-
STHS-LCDW).
To Next Page
Loading...
