What does it mean when the media misfeed message stays on my Oki C110 Printer?
If the media misfeed message stays on your Oki Printer, recheck the media path and make sure that you have removed all of the misfed media.
What to do if my Oki C110 is making unusual noises?
If you hear unusual noises from your Oki Printer, put the printer on a flat, hard, level surface. Also, check for any foreign object stuck inside the printer, and remove it. If you cannot remove it, contact Technical Support.
Why do the colors look wrong on my Oki C110 Printer?
If the colors look drastically wrong when printing with your Oki Printer, one or more of the toner cartridges may be defective. Remove the toner cartridges and verify that the toner is distributed evenly on each cartridge roller, and then reinstall the toner cartridges.
Why is the media wrinkled when printed from my Oki C110?
If the media is wrinkled when printed by your Oki Printer, it may be moist from humidity or have water spilled on it, so replace it with new, dry media. The media feed roller or fuser unit could also be defective, so check them for damage. If you are using unsupported media, consult the 'Print Media' section.
Why does my Oki Printer have toner smudges or residual images?
If there are toner smudges or residual images on prints from your Oki Printer, one or more of the toner cartridges may be defective or installed incorrectly. Remove the toner cartridges and check for damage; replace any damaged cartridges.
Why is my Oki C110 media misfeeding?
If the Oki Printer media is misfeeding, ensure the envelopes are loaded correctly in Tray 1 with the flaps facing down. If you're using unsupported media, consult the 'Print Media' section. Also, a dirty media feed roller can cause this issue, so clean the media feed roller.
What to do if my Oki Printer power is not on?
If the Oki Printer power is not on, confirm that the power cord is correctly plugged into the outlet. If it is, plug another electrical appliance into the outlet to see whether it operates properly. Also, ensure the power switch is turned on. Finally, make sure the printer is connected to an outlet with a voltage or frequency that matches the printer specifications.
How to fix low image density on my Oki C110?
If the image is too light or has low density on your Oki Printer, clean the print head window. If the media is moist, replace it with new, dry media. Also, the toner cartridge may be low, so replace it. Defective toner cartridges can also cause this, so remove them and check for damage, replacing if necessary. Finally, ensure the media type is correctly set in the printer driver, especially for envelopes, labels, postcards, thick stock, or letterheads.
Why does my Oki Printer take so long to print?
If printing takes too much time with your Oki Printer, it might be set to a slow printing mode. If you are using regular paper, make sure that the media type is set properly in the driver. The printer may be in power saving mode, which delays the start of printing. If the job is very complex, simply wait. Also, using a toner cartridge for a different region or an unapproved toner cartridge can slow down printing, so install a genuine Oki toner cartridge approved for your specific printer.
Why are colors not registering properly on Oki Printer?
If colors are not registering properly, or you notice colors are mixed or have page-to-page variation on your Oki Printer, it might be due to the imaging cartridge not being correctly seated. Remove the imaging cartridge and reinstall it. Also, one or more of the toner cartridges may be defective, so remove them and check for damage, replacing any damaged cartridges. Finally, the media could be moist from humidity, so replace it with new, dry media.
Step-by-step instructions for loading various types of media into the printer trays.
Detailed procedure for replacing individual toner cartridges in the printer.
Instructions for safely removing and installing the printer's imaging cartridge.
Guidance on replacing the fuser unit, including crucial safety warnings about heat.
Procedures for cleaning the printer's exterior and interior components.
Best practices and tips to avoid paper jams and misfeeds during printing operations.
Explanation of printer status, warning, error, and service messages displayed by indicators.
Step-by-step guide on how to safely remove misfed media without causing damage.
Troubleshooting common symptoms, causes, and solutions for media misfeed issues.
General| Color | Yes |
|---|---|
| Duplex printing | No |
| Maximum resolution | 600 x 1200 DPI |
| Time to first page (black, normal) | 13 s |
| Time to first page (color, normal) | 22 s |
| Print speed (black, normal quality, A4/US Letter) | 19 ppm |
| Print speed (color, normal quality, A4/US Letter) | 5 ppm |
| Internal memory | 16 MB |
| Sound power level (standby) | 29 dB |
| Sound pressure level (printing) | 51 dB |
| Total input capacity | 200 sheets |
| Total output capacity | 100 sheets |
| Maximum print size | 216 x 356 mm |
| ISO A-series sizes (A0...A9) | A4, A5 |
| ISO B-series sizes (B0...B9) | B5 |
| Maximum ISO A-series paper size | A4 |
| Supported media weight(s) | 60/209 g/m² |
| Compatible operating systems | Windows 2000 / XP / XP x64 / Vista (32 bit) / Vista (64 bit) / Server 2003 / Server 2003 x64 / Server 2008 / Server 2008 x64 |
| Maximum operating temperature range (T-T) | 10 - 35 °C |
| Recommended operating temperature range (T-T) | 15 - 25 °C |
| Maximum duty cycle | 250 pages per month |
| Sustainability certificates | ENERGY STAR |
| Power consumption (printing) | 440 W |
| Power consumption (PowerSave) | 14 W |
| Storage temperature (T-T) | -20 - 40 °C |
| Storage relative humidity (H-H) | 10 - 95 % |
| Operating relative humidity (H-H) | 15 - 85 % |
Weight and Dimensions| Dimensions (WxDxH) | 396 x 380 x 275 mm |
|---|
To Next Page
