沖データ企業秘密・OkiDataCONFIDENTIAL
45530603TX - 70/130
Category1
Category2 Category3
Category4
Item Value Default
機能
Valid
16K(184x260mm)[LEF]
16K(195x270mm)[LEF]
16K(197x273mm)[LEF]
8K(260x368mm)
8K(270x390mm)
8K(273x394mm)
Paper Feed MPTray
Tray1
Tray2
Tray3
Tray4
Tray5
*
Specifies a paper tray.
TRAY2 to 5: Displayed only if they are installed.
JE
Auto Tray Switch On
Off
* Sets the Auto Tray switching function. JE
Tray Sequence Down
Up
Paper Feed
*
Specifies selection order priority for switching Auto Tray
Select/Auto Tray Switch.
JE
Unit of Measurementinch
millimeter
*L
*A
Specifies the unit of custom paper size. JE
Duplex Last Page Skip Blank Page
Always Print
* When Skip Blank Page is selected, the last page of an
odd-page duplex print job is printed as Simplex.
When Always Print is selected, the printer operates as
usual.
[Condition for display]
・A Duplex Unit is installed.
JE
System Adjust Power Save Time 1 minute
2 minutes
3 minutes
4 minutes
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
*
Sets time to wait for moving to Power Save mode.
Moves to Power Save mode even during an error.
ET
Sleep Time 1 minute
2 minutes
3 minutes
4 minutes
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
*
Sets the time to switch from Power Save mode
mode.
The start point is the moment when the printer goes into
PowerSave.
ET
Auto Power Off Time1 hour
2 hours
3 hours
4 hours
8 hours
12 hours
18 hours
24 hours
*
Set the time to switch from Idle state to Off mode. ET
Clearable Warning
ONLINE
Job
* Sets display deletion timing of clearable warnings.
PS: JOB only
ET
Auto Continue On
Off
*
Sets whether a printer is automatically recovered or not
when memory overflow/tray request occurs.
(Wait time for recovery: 15 sec)
ET
Manual Timeout Off
30 seconds
60 seconds
*
Sets time to wait for paper to be fed in manual feed.
If paper is not fed within this period of time, the job is
canceled.
ET
Wait Timeout Off
5 seconds
10 seconds
20 seconds
30 seconds
40 seconds
50 seconds
60 seconds
90 seconds
120 seconds
150 seconds
180 seconds
210 seconds
240 seconds
270 seconds
300 seconds
*
Sets time between stopping reception of job data and
performing force printing.
Does not perform printing and cancels that job instead
in the case of PS.
"Timeout Local" defaults to 40Sec. and "Timeout
Network" defaults to 90Sec. They can not be changed
through menu settings.
ET
Low Toner Continue
Stop
* Sets printer operation when Toner Low is detected.
In CONTINUE, the printer can continue printing while
remaining ON-LINE.
In STOP, it becomes OFF-LINE.
ET
Jam Recovery On
Off
*
Sets whether JAM RECOVERY printing is performed or
not when Jam occurs.
When it is set to OFF, a job that includes the page to
which Jam has occurred will be cancelled.
JE
Error Report On
Off
*
Sets whether an error report is printed or not when an
internal error occurs.
Valid only for PS、PCL XL and XPS.
JE
Hex Dump Execute
−
Prints out data received from the host PC in the
hexadecimal Dump. Turning off the power supply
switch restores Normal Mode from HEX Dump Mode.
If Execute is selected, exit from the menu.
JE
Print Adjust Print Position
Adjust
MPTray
X Adｊust
0.00millimeter
+0.25millimeter
~
+2.00millimeter
-2.00millimeter
~
-0.25millimeter
* For the paper fed from MPTray
Adjusts the position of a whole print image in the
direction that is perpendicular to the direction paper
runs, that is horizontally (at 0.25 mm pitch).
Any parts of the print image that go beyond the
printable area as a result of this designation are
clipped.
JE
Y Adjust 0.00millimeter
+0.25millimeter
~
+2.00millimeter
-2.00millimeter
~
* For the paper fed from MPTray
Adjust the position of a whole print image in the
direction paper runs, that is vertically (at 0.25mm pitch).
Any parts of the print image that go beyond the
printable area as a result of this designation are
clipped.
JE
To Next Page
Loading...
