Oki C911 - Page 80

沖データ企業秘密・OkiDataCONFIDENTIAL 
45530603TX - 80/130
Category1 Category2 Category3 Category4 Item Value Default
機能
Valid
deselects Auto CR/LF mode, or equivalently, selects
whether to perform auto CR and LF when the cursor for
text exceeds the right margin of paper while the text is
continuously input.
White Page Skip On
Off *
Sets whether to eject or not a page without any data to
print (blank page) upon reception of FF command
(OCH) in PCL Mode. OFF: Ejecting.
JE
CR Function CR
CR+LF
* Sets performance when CR code is received in PCL.
CR: Carriage Return
CR+LF: Carriage Return and Line Feed
JE
LF Function LF
LF+CR
* Sets performance when LF code is received in PCL.
LF: Line Feed
LF+CR: Line Feed and Carriage Return
JE
Print Margin Normal
1/5 inch
1/6 inch
* Sets a non-printable area of paper.
The width of the area along the right and left sides of
paper (left and right of paper laid out according to paper
orientation) paper outside the printable area
NORMAL: PCL emulation compatible, approximately
1/4~1/4.3INCH (depending on paper) is outside the
printable area.
Fixed at 1/6INCH for HP-GL2.
JE
True Black On
Off *
PCL: Sets if to use Composite Black (cmyk mixed) or
Pure Black (K only) for the black (100%) in image data.
OFF: Mode using Composite Black
ON: Mode using Pure Black
This is not available for PS.
JE
Pen Width Adjust On
Off
* When the minimum width is specified in PCL, if you
draw a 1-dot line, it sometimes looks broken.
With PEN WIDTH Adjust set to ON, when the minimum
width is specified, the line width will be emphasized so
as to look wider than a 1-dot line.
With PEN WIDTH Adjust set to OFF, the line will
appear as specified.
JE
Tray ID# MPTray 1
~
4
~
59
*
Sets the # to specify the MPTray for the paper feed
destination command (ESC&l#H) in PCL5e emulation
JE
Tray1 1
~
5
~
59
* Sets the # to specify Tray 1 for the paper feed
destination command (ESC&l#H) in PCL5e emulation.
JE
Tray2 1
~
5
~
59
*
Sets the # to specify Tray 2 for the paper feed
destination command (ESC&l#H) in PCL5e emulation.
Displayed only if the Tray 2 is installed.
JE
Tray3 1
~
20
~
59
*
Sets the # to specify Tray 3 for the paper feed
destination command (ESC&l#H) in PCL5e emulation.
Displayed only if the Tray 3 is installed.
JE
Tray4 1
~
21
~
59
*
Sets the # to specify Tray 4 for the paper feed
destination command (ESC&l#H) in PCL5e emulation.
Displayed only if the Tray 4 is installed.
JE
Tray5 1
~
22
~
59
*
Sets the # to specify Tray 5 for the paper feed
destination command (ESC&l#H) in PCL5e emulation.
Displayed only if the Tray 5 is installed.
JE
XPS Setup DigitalSignature Print Invalid Sign
Print Only Valid Sign
Off *
Sets up the DigitalSignature function. (The default is
Off.)
Print Invalid Sign: If a document has been tampered,
the printer prints a normal print report and a temper
error report.
Print Only Valid Sign: If a document has been
tampered, the printer prints only a tamper error report.
Off: No signatures are verified.
JE
DiscardControl Auto
Each Page
Off
* Sets up the DiscardControl function. (The default is
Auto.)
Auto: Frees resources as necessary.
EachPage: Frees resources page by page according to
markups.
Off: Disables the DiscardControl function.
JE
MC Mode On
Off
* Sets up the MarkupComaptibility function. (The default
is On.)
On: Uses the MarkupComaptibility function.
Off: Not use the MarkupComaptibility function.
JE
Unzip Mode Auto
Speed
Print
*
Specifies the unzip method for XPS flies.
(The default is
Speed.)
Auto: Automatically switches modes depending on files.
Speed: Prioritizes print speed and doesn't use the
partial Unzip function.
Print: Prioritizes print processing and uses the partial
Unzip function.
JE
White Page Skip On
Off *
Sets whether or not to eject pages that contain no
print data (blank pages) using XPS.
When Off is selected, blank pages are ejected, if any.
(The default is Off.)
JE
IBM PPR Setup Character Pitch 10 CPI
12 CPI
17 CPI
20 CPI
Proportional
* Specifies character pitch in IBM PPR emulation.
(Not available with products for Japan.)
JE
Font Condense 12CPI to 20CPI
12CPI to 12CPI
* Specifies 12CPI pitch for Condense Mode.
(Not available with products for Japan.)
JE
Character Set SET-2
SET-1
* Sets a character set.
(Not available with products for Japan.)
JE
Symbol Set IBM-437
IBM-850
IBM-860
* Sets a symbol set.
(Not available with products for Japan.)
JE