A-15
Appendices
CJ-series PROFIBUS Master Unit Operation Manual for NJ-series CPU Unit (W509)
A-5 CX-ConfiguratorFDT Warning and Error Messages
App
The table below lists the Error messages which can be displayed by the PROFIBUS Master Unit DTM
in case there are configuration errors. Usually, these are detected either when entering, or up on down-
load. The table suggests corrections to the problems in the right most column.
07 [IO area] must be empty.
Move all modules into other
area
• [IO area] = output area1/
output area2/ input area1/
input area2
“Not used” item in the start address combo box in
output/input allocation tabs can only be selected if
there are no I/O module mapped in that area.
• OKClose message box. Move modules to other
I/O area first.
When selecting the “Not
Used” item from the
memory area box.
08 Slave_User_data part of the
PROFIBUS slave parameter
set will be ignored. See slave
[no]-[name]
[no] = slave address
[name] = slave DTM name
Slave_User_data part of the slave parameter set
will not be used. The additional user parameters
in the slave parameter set are not supported by
the PROFIBUS Master Unit.
• OK: Close message box
When adding a slave
DTM to the network,
which defines additional
user parameters.
09 Auto addressing will reallo-
cate slave I/O mapping.
Would you like to proceed?
When selecting the Auto-Addressing check box in
the Master Setup tab, all slave I/O data mappings
will be compressed in each of the I/O mappings.
The slave I/O mapping will be changed.
• Yes: Update slave I/O module mapping and
check checkbox.
• No: Do not update slave I/O module mapping
and uncheck checkbox.
When checking the Auto-
Addressing checkbox on
the Master Setup tab.
10 Settings cannot be uploaded,
unit must be restarted. Would
you like to continue?
The settings uploaded were not used by stack
• Yes: Restart the unit and upload the settings.
• No: Do nothing.
When attempting to
upload settings.
11 Upload is not supported. Upload is not supported
OK: Close message box.
When attempting to
upload settings.
12 After locking address it can-
not be changed any more.
Would you like to proceed?
When sending Set Device Station Address com-
mand with 'Lock' check box is checked, the
address will be stored permanently in the Slave
device and can not be changed anymore.
• Yes: Lock option is checked.
• No: Lock option is unchecked.
When ‘Lock’ check box in
the Set Device Station
Address GUI is checked.
13 PROFIBUS DP-V1 alarms
are not supported by the
Master Unit and will be dis-
abled.
Alarm settings set by the Slave DTM are not sup-
ported and will be reset.
• OK: Close message box.
Downloading settings and
one of the alarm bits are
set in Slave Parameter
Set.
14 Publisher functionality is not
supported by the Master Unit
and will be disabled.
Publisher functionality set by the Slave DTM is not
supported and will be reset.
• OK: Close message box.
Downloading settings and
the Publisher bit is set in
Slave Parameter Set.
15 Isochronous mode is not sup-
ported by the Master Unit and
will be disabled.
Isochronous mode set by the Slave DTM is not
supported and will be reset.
• OK: Close message box.
Downloading settings and
the Isochronous mode bit
is set in Slave Parameter
Set.
16 Acyclic Connection / Abort
Status Area and Acyclic Slave
Timeout settings are not sup-
ported by the Master Unit and
will be disabled.
The connected Master Unit has version V2.00.
The new features for version V3.00 (and up) are
not supported by the Master Unit.
Downloading settings to
Master Unit V2.00 with
Master DTM V3.00 (or
higher).
Configuration Error Messages
Number Message Description When occurring
To Next Page
Loading...
