– 170 –
Chapter 8 Display — Screen status display
[FUNCTION] screen
Displays the video output status and information of the recording media.
Item Description
[SDI OUT] — Displays the status of the signal output from the <SDI OUT1> terminal.
[TYPE]
Displays the format of the signal output from the <SDI OUT1> terminal by [HD-SDI]/
[SD-SDI].
[CHAR]
Displays the superimposition status of characters selected in the main menu → [IN/OUT
SEL] → [SDI OUT1 CHAR] by [ON]/[OFF].
[P2CARD STATUS]
—
Displays the status of the P2 card inserted in the card slot, remaining capacity, and total
used capacity.
The statuses of cards to be displayed are as follows:
[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/
[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]
For details, refer to “P2 card access LEDs and status of P2 cards” (page 48).
[TOTAL P2/mP2] Displays the remaining capacity/total capacity of slots 1 and 2 altogether.
[SLOT1] Displays the status of the P2 card in slot 1 and remaining capacity/total capacity.
[SLOT2] Displays the status of the P2 card in slot 2 and remaining capacity/total capacity.
[PROXY]
[MEDIA]
Displays the media selection status for proxy recording.
[P2]/[P2&SD]/[OFF]
[MODE]
Displays the setting status for proxy recording mode.
[AVC-G6 2CH MOV]/[SHQ 2CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV]
[PROXY ERROR] Displays the operation error on the proxy module.
[NETWORK] [NETWORK] Displays the network to be used and its status.
[AUDIO] screen
Displays audio settings and the selection status of each recording channel.
Item Description
[AUDIO] [SAMPLE RES] Displays the audio recording bits.
[A.IN]
[CH1/2/3/4]
Displays the input status of each channel.
[FRONT] (front), [REAR] (rear), [W.L.] (wireless)
[LEVEL]
[CH1/2/3/4]
Displays the recording level adjustment method currently selected on each channel.
f [MANU]: Displayed when manual adjustment is set.
f [AUTO]: Displayed when automatic adjustment is set.
Settings are performed in the SmartUI [AUD01:LEVEL] screen.
[F.VR]
[CH1/2/3/4]
Displays by [ON]/[OFF] whether the <F.AUDIO LEVEL> dial is enabled on the channel to
which [VR] (manual adjustment by adjustment dial) is displayed in [LEVEL].
[LIMITER] [CH1/2/3/4] Displays the limiter settings of each channel.
[LOWCUT] [CH1/2/3/4] Displays the lowcut lter status of each channel.
[METER] [CH1/2/3/4] Displays the recording level of each channel.
[USER SW] screen
Displays the assignment status of each USER button. For details, refer to “Assigning functions to USER buttons” (page 66).
Item Description
[OTHER ASSIGN] [GAIN L] Displays the gain value assigned to <L> of the <GAIN> switch.
[GAIN M] Displays the gain value assigned to <M> of the <GAIN> switch.
[GAIN H] Displays the gain value assigned to <H> of the <GAIN> switch.
[S.GAIN] Enumerates and displays the gain value assigned as super gain.
[WHITE BAL
A]
Displays the color temperature assigned to <A> of the <WHITE BAL> switch.
[WHITE BAL B] Displays the color temperature assigned to <B> of the <WHITE BAL> switch.
[WHITE BAL
PRE]
Displays the color temperature assigned to <PRST> of the <WHITE BAL> switch.
[USER SW] [USER M] Displays the assignment to the <USER MAIN> button.
[USER 1] Displays the assignment to the <USER1> button.
[USER 2] Displays the assignment to the <USER2> button.
[RET SW] Displays the assignment to the <RET> button on the lens.
[CAC INFO] screen
Display the operation status or information of CAC.
Item Description
[CAC CONT] Displays the operation status of CAC.
f [ON]: [ON] has been set in the main menu → [MAINTENANCE] → [CAC ADJ.] → [CAC CONTROL] and CAC is active.
f [STOP]: [ON] has been set in the main menu → [MAINTENANCE] → [CAC ADJ.] → [CAC CONTROL], however, CAC
operation stops under certain data or lens conditions.
f [OFF]: [OFF] has been set in the main menu → [MAINTENANCE] → [CAC ADJ.] → [CAC CONTROL] and CAC is not
active.
To Next Page
Loading...
