Panasonic AJ-PX800G - [Card Functions]; [Other Functions]

– 141 –
Chapter 6 Menu Operations — Menu list
Item Description of settings
[BATT STAT NEAR END] Selects the near end percent value.
When the battery charge level percentage cannot be detected, this will follow the near end voltage value
set for [TYPE A].
[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]
f Factory setting: [5%]
If a battery whose remaining charge is displayed in units of 10% is used, the setting value and actual near
end warning may vary slightly.
[BATT STAT END] Selects the end percent value.
When the battery charge level percentage cannot be detected, this will follow the end voltage value set for
[TYPE A].
[1%]…[10%]
f Factory setting: [1%]
When using a battery which displays battery charge level by units of 10%, an end is determined only in two
stages: when it is set between [1%] and [5%], or when it is set between [6%] and [10%].
[ENDURA STAT NEAR
END]
Selects the near end percent value.
When the battery charge level percentage cannot be detected, this will follow the near end voltage value
set for [TYPE A].
[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]
f Factory setting: [5%]
If a battery whose remaining charge is displayed in units of 10% is used, the setting value and actual near
end warning may vary slightly.
[ENDURA STAT END] Selects the end percent value.
When the battery charge level percentage cannot be detected, this will follow the end voltage value set for
[TYPE A].
[1%]…[10%]
f Factory setting: [1%]
When using a battery which displays battery charge level by units of 10%, an end is determined only in two
stages: when it is set between [1%] and [5%], or when it is set between [6%] and [10%].
[CARD FUNCTIONS]
Congure the settings regarding reading/writing of the scene les and user les to SD memory cards.
Item Description of settings
[SCENE FILE] Loads scene les from an SD memory card or saves them to an SD memory card.
[LOAD]: Loads scene les.
[SAVE]: Saves scene les.
[USER FILE] Loads user les from an SD memory card or saves them to an SD memory card.
[LOAD]: Loads user les.
[SAVE]: Saves user les.
[CAC FILE] Loads CAC les from an SD memory card or deletes CAC les stored in the SD memory card.
[LOAD]: Loads CAC les. Species the le number when saving a loaded CAC le in the SD memory card
to the camera.
[DELETE]: Deletes CAC les stored in the SD memory card.
[SD CARD PROPERTY] Displays the SD memory card status. The format condition, available space, etc. can be checked.
[FORMAT SD CARD] Formats an SD memory card.
[OTHER FUNCTIONS]
Congure these items to make settings for reading/writing, initialization of user le data on the internal memory, and the camera settings.
Item Description of settings
[USER FILE] Loads/saves/initializes user les on the camera memory.
[LOAD]: Loads user les.
[SAVE]: Saves user les.
[INITIALIZE]: Restores user les to the factory settings.
[ACCESS LED] Selects whether to light the access LED of the P2 card.
[ON], [OFF]
f Factory setting: [ON]
[REC TALLY] Sets the tally lamp display in the viewnder.
[RED]: Illuminates the red tally lamp on the viewnder during recording with the camera. The front tally
lamp and the back and rear tally lamps on the body are also illuminated.
[GREEN]: Illuminates the green tally lamp in the viewnder during recording with the camera. The front
tally lamp or the tally lamps on the body are not illuminated
[CHAR]: During recording with the camera, the tally lamp in the viewnder is not illuminated and the
recording status is displayed only with text on the screen. No tally lamps are illuminated.
f Factory setting: [RED]
[CLOCK SETTING] Sets the built-in calendar (date and time).
[TIME ZONE]
For GMT, set using 30 minute intervals from −12:00 to +13:00 (however, +12:45 is possible). After setting
the time, when changing the setting value for [TIME ZONE], the displayed and registered times switch to
the time with the time difference.