Panasonic AJ-PX800G - Mode Check Display

– 159 –
Chapter 8 Display — Screen status display
No Item Shooting Playback
<DISP/
MODE CHK>:
<CHK>
<DISP/MODE
CHK>: <OFF>
<DISP/MODE CHK>: <ON>
[OTHER DISPLAY]
[ALL] [PARTIAL] [USER]
16 Y GET brightness display
l
—
l
—
l l l
17 ND lter display
l
—
l
—
l
—
l
18 Shutter speed display
l
—
l
—
l l l
19 <WHITE BAL> switch position display
l
—
l
—
l l l
20 Gain display
l
—
l
—
l l l
21 Iris display
l
—
l
—
l l l
22 Zoom position display
l
—
l
— —*
1
—*
1
—*
1
23 Focus control information display
l
—
l
— —*
1
—*
1
—*
1
24 Recommended ND lter display
l
—
l
— —*
1
—*
1
—*
1
25 Camera warning, notication display area
l l l l
—*
1
—*
1
—*
1
26 Automatic white balance abnormal display
l
—
l
— — — —
27 Automatic black balance abnormal display
l
—
l
— — — —
28
Chromatic aberration compensation
function display
l
—
l
—
l l l
29 Lens extender display
l
—
l
—
l l l
30 Flash band compensation function display
l
—
l
—
l l l
31 Dynamic range stretcher function display
l
—
l
—
l l l
32 Scene le name display
l
—
l
—
l
—
l
33 Battery charge level indicator
l l l
—*
2
—*
1
—*
1
—*
1
34 P2 card remaining free space
l l l
—*
2
—*
1
—*
1
—*
1
35 Simultaneous recording mode display
l
—
l
—
l
—
l
36 High-sensitivity mode display
l
—
l
—
l l l
37 One clip recording mode status display
l
—
l
—
l l l
38
Recording/playback operation status
display
l l l
—*
3
l l l
39 Rec during upload status display
l l
— — —*
1
—*
1
—*
1
40 Streaming distribution status display
l l
— — —*
1
—*
1
—*
1
41
HD SDI REMOTE recording status and
4G/LTE connection status display
l
*4
—
l
*4
—
l
*4
l
*4
l
*4
*1 May be displayed depending on other settings.
*2 Displayed when the remaining capacity becomes smaller.
*3 Displayed during shooting.
*4 Always displayed when [HD SDI REMOTE] is set or when 4G/LTE connection is set.
Mode check display
The camera settings and status can be displayed on the viewnder.
Each time the <DISP/MODE CHK> switch on the camera is pushed towards the <CHK> side, the ve screens are switched.
[STATUS] screen display → [FUNCTION] screen display → [AUDIO] screen display → [USER SW] screen display → [CAC INFO] screen display → no
display
Each screen is displayed for approximately ve seconds. Pushing the <DISP/MODE CHK> switch towards the <CHK> side while the screen is displayed
moves to the next screen.
[FUNCTION] screen
Displays the video output status and information of the recording media.
[SDI OUT] — Displays the status of the signal output from the <SDI OUT/IN (OP)> terminal.
[TYPE]
Displays the format of the signal output from the <SDI OUT/IN (OP)> terminal by [HD-SDI]/
[SD-SDI].
[CHAR]
Displays the superimposition status of characters selected in the main menu → [IN/OUT
SEL] → [SDI OUT CHAR] by [ON]/[OFF].
[P2CARD STATUS]
—
Displays the status of the P2 card inserted in the card slot, remaining capacity, and total
used capacity.
The statuses of cards to be displayed are as follows:
[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/
[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]
For details, refer to “P2 card access LEDs and status of P2 cards” (page 43).
[TOTAL P2/mP2] Displays the remaining capacity/total capacity of slots 1 and 2 altogether.
[SLOT1] Displays the status of the P2 card in slot 1 and remaining capacity/total capacity.
[SLOT2] Displays the status of the P2 card in slot 2 and remaining capacity/total capacity.