Panasonic AJ-PX800G - Page 160

– 160 –
Chapter 8 Display — Screen status display
[PROXY]
[MEDIA]
Displays the media selection status for proxy recording.
[P2]/[P2&SD]/[OFF]
[MODE]
Displays the setting status for proxy recording mode.
[AVC-G6 2CH MOV]/[SHQ 2CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV]
[PROXY ERROR] Displays the operation error on the proxy module.
[NETWORK] [NETWORK] Displays the network to be used and its status.
[AUDIO] screen
Displays audio settings and the selection status of each recording channel.
[AUDIO] [SAMPLE RES] Displays the audio recording bits.
[A.IN]
[CH1/2/3/4]
Displays the input status of each channel.
[FRONT] (front), [REAR] (rear), [W.L.] (wireless)
[LEVEL]
[CH1/2/3/4]
Displays the recording level adjustment method currently selected on each channel.
f [MANU]: Displayed when manual adjustment is set.
f [AUTO]: Displayed when automatic adjustment is set.
Settings are performed in the SmartUI [AUD01:LEVEL] screen.
[F.VR]
[CH1/2/3/4]
Displays by [ON]/[OFF] whether the <F.AUDIO LEVEL> dial is enabled on the channel to
which [VR] (manual adjustment by adjustment dial) is displayed in [LEVEL].
[LIMITER] [CH1/2/3/4] Displays the limiter settings of each channel.
[LOWCUT] [CH1/2/3/4] Displays the lowcut lter status of each channel.
[METER] [CH1/2/3/4] Displays the recording level of each channel.
[USER SW] screen
Displays the assignment status of each USER button. For details, refer to “Assigning functions to USER buttons” (page 60).
[OTHER ASSIGN] [GAIN L] Displays the gain value assigned to <L> of the <GAIN> switch.
[GAIN M] Displays the gain value assigned to <M> of the <GAIN> switch.
[GAIN H] Displays the gain value assigned to <H> of the <GAIN> switch.
[S.GAIN] Enumerates and displays the gain value assigned as super gain.
[WHITE BAL A] Displays the color temperature assigned to <A> of the <WHITE BAL> switch.
[WHITE BAL B] Displays the color temperature assigned to <B> of the <WHITE BAL> switch.
[WHITE BAL PRE] Displays the color temperature assigned to <PRST> of the <WHITE BAL> switch.
[USER SW] [USER M] Displays the assignment to the <USER MAIN> button.
[USER 1] Displays the assignment to the <USER1> button.
[USER 2] Displays the assignment to the <USER2> button.
[RET SW] Displays the assignment to the <RET> button on the lens.
[CAC INFO] screen
Display the operation status or information of CAC.
[CAC CONT] Displays the operation status of CAC.
f [ON]: [ON] has been set in the main menu → [MAINTENANCE] → [CAC ADJ.] → [CAC CONTROL] and CAC is active.
f [STOP]: [ON] has been set in the main menu → [MAINTENANCE] → [CAC ADJ.] → [CAC CONTROL], however, CAC
operation stops under certain data or lens conditions.
f [OFF]: [OFF] has been set in the main menu → [MAINTENANCE] → [CAC ADJ.] → [CAC CONTROL] and CAC is not
active.
[CAC MODE] Displays the operation mode of CAC.
f [AUTO]: The CAC le is automatically selected.
[CONNECT LENS TYPE] Displays the lens ID of the currently connected digital lens.
[SELECT FILE TITLE] Displays the title and the le version of the CAC le currently used in the operation. The CAC le can be set in the main menu
→ [MAINTENANCE] → [CAC ADJ.].
[CAC WARNING] Displays a warning when operation of CAC has stopped.
f [CAC LENS DATA INVALID]: This is displayed, for example, when the response data from the lens is not supported.
f [LENS INIT. NOT COMPLETED]: This is displayed, for example, when initialization of the lens cannot complete.
f [CAC FILE DATA NOT FOUND]: Displayed when the chromatic aberration compensation function is set to [ON] and the
chromatic aberration compensation data matching the connected lens.