Panasonic KX-FLB802CX

15
KX-FLB802CX/KX-FLB812CX/KX-FLB802CXS/KX-FLB812CXS
D12 VDD33 - 3.3V POWER SOURCE
D13 VDD33 - 3.3V POWER SOURCE
D14 VDD18 - 1.8V POWER SOURCE
D15 VDD18 - 1.8V POWER SOURCE
D16 PRIO[0] O 3.3V OUTPUT PORT(PVCLK)
D17 TEST I 3.3V(5V torelant) NOT USED
D18 RESET I 3.3V(5V torelant) RESET INPUT
E1 SBA[13] O 3.3V SYSTEM ADDRESS BUS 13
E2 SBA[12] O 3.3V SYSTEM ADDRESS BUS 12
E3 GPIO[30] I 3.3V(5V torelant) INPUT PORT(LANRDY)
E4 VDD18 - 1.8V POWER SOURCE
E15 VDD18 - 1.8V POWER SOURCE
E16 PRIO[1] O 3.3V OUTPUT PORT(WP)
E17 PRIO[2] I 3.3V(5V torelant) INPUT PORT(R/B)
E18 PRIO[3] O 3.3V OUTPUT PORT(DEVAC)
F1 GPIO[33] O 3.3V OUTPUT PORT(XLANRST)
F2 GPIO[32] O 3.3V NOT USED
F3 GPIO[31] O 3.3V OUTPUT PORT(XMDMRST1)
F4 VDD33 - 3.3V POWER SOURCE
F15 VDD33 - 3.3V POWER SOURCE
F16 PRIO[4] O 3.3V OUTPUT PORT(PVDATA0)
F17 PRIO[5] O 3.3V OUTPUT PORT(PVDATA1)
F18 PRIO[6] O 3.3V OUTPUT PORT(PVDATA2)
G1 SMOT[2] O 3.3V NOT USED
G2 SMOT[1] O 3.3V OUTPUT PORT(FAN1FULL)
G3 SMOT[0] O 3.3V OUTPUT PORT(FAN1HALF)
G4 VDD33 - 3.3V POWER SOURCE
G7 VSS18 - GND GND
G8 VSS33 - GND GND
G9 VSS33 - GND GND
G10 VSS33 - GND GND
G11 VSS33 - GND GND
G12 VSS18 - GND GND
G15 VDD33 - 3.3V POWER SOURCE
G16 PRIO[7] O 3.3V OUTPUT PORT(PVDATA3)
G17 PRIO[8] O 3.3V OUTPUT PORT(CIDRLY)
G18 PRIO[9] O 3.3V OUTPUT PORT(SPMUTE)
H1 SMOT[5] O 3.3V OUTPUT PORT(SN_REG)
H2 SD[3] O 3.3V NOT USED
H3 SMOT[4] O 3.3V NOT USED
H4 VSSA33 - GND GND
H7 VSS33 - GND GND
H8 VSS18 - GND GND
H9 VSS18 - GND GND
H10 VSS18 - GND GND
H11 VSS18 - GND GND
H12 VSS33 - GND GND
H15 VDD18 - 1.8V POWER SOURCE
H16 PRIO[10] O 3.3V OUTPUT PORT(LINELRY1)
H17 PRIO[11] I 3.3V(5V torelant) INPUT PORT(BELL1)
H18 PRIO[12] O 3.3V OUTPUT PORT(P-SHORT1)
J1 VDDA33 - 3.3V POWER SOURCE
J2 SD[5] I 3.3V(5V torelant) CIS INTERFACE
J3 SMOT[3] O 3.3V OUTPUT PORT(SN_ST)
J4 VDD18 - 1.8V POWER SOURCE
J7 VSS33 - GND GND
J8 VSS18 - GND GND
J9 VSS18 - GND GND
J10 VSS18 - GND GND
J11 VSS18 - GND GND
J12 VSS33 - GND GND
J15 VDD33 - 3.3V POWER SOURCE
J16 PRIO[13] O 3.3V NOT USED
J17 PRIO[14] O 3.3V NOT USED
J18 PRIO[15] O 3.3V NOT USED
K1 SD[7] I 3.3V(5V torelant) CIS INTERFACE
K2 SD[1] O 3.3V(5V torelant) NOT USED
PIN No. SIGNAL I/O POWER SUPPLY VOLTAGE EXPLANATION