Panasonic KX-NS1000 User Manual (English)

Other manuals for Panasonic KX-NS1000

User Guide528 pages

Feature Manual482 pages

Guide542 pages

Pc Programming Manual1294 pages

Operating Manual366 pages

Installation Manual416 pages

User Manual384 pages

Getting Started58 pages

Features Guide20 pages

Quick Reference Guide28 pages

Questions and Answers:

A
Alvin SalazarAug 27, 2025
What to do if I cannot make or receive calls via IP network on my Panasonic KX-NS1000?
- M
  Mr. Tristan StewartAug 27, 2025
  If you cannot make or receive calls via an IP network using your Panasonic PBX, the issue could stem from several causes: a malfunctioning DSP card (in which case, replace the card), a faulty motherboard (replace the motherboard, ensuring the PBX is off during replacement), or an insufficient number of activation keys (purchase additional keys from a certified dealer). Poor connection can also be the culprit; ensure an 8-pin twisted pair cable is used, CAT 5/CAT 5e cables are not over 100m, and a straight cable connects to the switching hub. Finally, a network malfunction may be to blame, so verify all network devices are on and no unwanted firewall is present.
M
margaret14Sep 10, 2025
How do I fix noise on external paging with my Panasonic PBX?
- Q
  qmcgeeSep 10, 2025
  To eliminate noise on external paging with your Panasonic PBX: Use a shielded cable as the connection wire between the PBX and amplifier. A short shielded cable is recommended.
A
amydonaldsonAug 28, 2025
What to do if the LINK indicator of the mother board does not turn on my Panasonic PBX?
- C
  Christopher MelendezAug 28, 2025
  If the LINK indicator on your Panasonic PBX motherboard isn't lighting up, it could be due to a motherboard malfunction, in which case you should replace the motherboard after turning off the PBX. Another potential cause is a poor connection. To resolve this, ensure an 8-pin twisted pair cable is used for the connection, that none of the CAT 5/CAT 5e cables in use are over 100 m in length, and that a straight cable is used for connection to a switching hub. Finally, a network malfunction could be the cause, so ensure all network devices in use are switched on.
M
Michelle DavisAug 28, 2025
What to do if extensions (except IP-PT/ SIP phone) do not operate on my Panasonic PBX?
- B
  Brandon HallAug 28, 2025
  If extensions (excluding IP-PT/SIP phones) aren't working on your Panasonic PBX, it could be due to a few reasons. First, the extension card might be faulty, so try replacing it. Second, there could be a poor connection between the PBX and the extension. To test this, plug the extension into the same extension port using a short telephone cord; if it works, the connection between the PBX and the extension needs repair. Third, a telephone with an A-A1 relay might be connected. Make sure a 2-wire cord is used and the A-A1 relay switch is in the "OUT" or "OFF" position. Lastly, the extension itself could be malfunctioning. Plug it into another working extension port; if it still doesn't work, replace the extension.
A
Anna YatesSep 12, 2025
What to do if my Panasonic Telephone does not respond when buttons are pressed?
- W
  wwongSep 13, 2025
  If your Panasonic Telephone is locked, it will not respond when buttons are pressed. Unlock your telephone.
M
Maria McdonaldSep 8, 2025
How to correct the date and time on Panasonic KX-NS1000 PBX?
- K
  Kenneth WilliamsSep 8, 2025
  If the date and time are not correct on your Panasonic PBX, set the date and time by system programming. Consult your dealer.
L
Leon BanksSep 6, 2025
Why did PC and fax machine communication fail on my Panasonic KX-NS1000?
- K
  Kimberly HamiltonSep 6, 2025
  If the PC and fax machine communication failed on your Panasonic PBX system, an indication tone may have interrupted communication.
L
Lori KleinAug 29, 2025
Why can't I set the IP address, subnet mask address, and PBX IP address to the IP-PT on my Panasonic KX-NS1000 PBX?
- R
  ryan88Aug 29, 2025
  If you're unable to set the IP address, subnet mask address, and PBX IP address to the IP-PT on your Panasonic PBX, it's likely because you are setting an unusable value. Ensure you set an IP address within the valid range. For the IP address of the IP-PT/PBX, use a value between "1.0.0.0" and "223.255.255.255". For the subnet mask address, use a value between "0–255.0–255.0–255.0–255", excluding "0.0.0.0" and "255.255.255.255".
N
Nancy BurkeAug 29, 2025
What to do if the IP-PT cannot connect to the Panasonic KX-NS1000 PBX?
- L
  Lisa HernandezAug 29, 2025
  If your IP-PT cannot connect to the Panasonic PBX, several factors could be responsible. First, the IP address, subnet mask address, PBX IP address, or default gateway address may have been entered incorrectly; check each parameter and enter the correct value. Second, the Ethernet cable might not be connected properly; check the Ethernet cable connections. Third, the DHCP server may not be active; restart the external DHCP server, confirm whether the DHCP Server feature is enabled, or disable DHCP and re-enter settings as appropriate.
W
William AllenAug 30, 2025
Why can't I register the IP-PT on my Panasonic PBX?
- J
  jburtonAug 30, 2025
  If you're having trouble registering the IP-PT on your Panasonic PBX, it's likely because the necessary network parameters haven't been set. If you're not using the DHCP Server feature or an external DHCP server, make sure to set the IP address, subnet mask address, and enter the PBX IP address. If necessary, also enter the IP address of the default gateway. If you are using the DHCP Server feature or an external DHCP server, simply enter the PBX IP address.

Panasonic KX-NS1000 Specifications

General

Type	Hybrid IP-PBX
Max Concurrent Calls	256
VoIP Protocols	SIP, H.323
Power Supply	AC 100-240V, 50/60Hz
Maximum Extensions	1, 000
IP Extensions	1000
Operating Temperature	0°C to 40°C
Humidity	10 to 90% (non-condensing)
Max Users	1000