Panasonic PT-RQ32K

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 159
Note
f The power indicator <ON (G)/STANDBY (R)> will blink slowly in green while the no signal lights-out function is operating and the light source
is turned off.
f When [NO SIGNAL LIGHTS-OUT] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on
again from the condition that the light source has turned off by this function.
g When the signal is input
g When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed
g When the power on <b> button is pressed
g When the operation to disable the shutter function (shutter: open) is performed, such as pressing the <SHUTTER> button
g When the operating environment temperature is around 0 °C (32 °F) and the light source is forced to turn on due to warm-up
f The no signal lights-out function is disabled when the [DISPLAY OPTION] menu → [BACK COLOR] is set to either [DEFAULT LOGO] or
[USER LOGO] and the Panasonic logo or the image registered by the user is displayed on the projected image.
[INITIAL STARTUP]
Set the startup method when the <MAIN POWER> switch is set to <ON>.
1) Press as to select [INITIAL STARTUP].
2) Press qw to switch the item.
f The items will switch each time you press the button.
[LAST MEMORY] Starts up the projector in the condition before the <MAIN POWER> switch is set to <OFF>.
[STANDBY] Starts up the projector in standby.
[ON] Starts projecting immediately.
[STARTUP INPUT SELECT]
Set the input when the projector is switched on to start projection.
1) Press as to select [STARTUP INPUT SELECT].
2) Press the <ENTER> button.
f The [STARTUP INPUT SELECT] screen is displayed.
3) Press asqw to select the input, and press the <ENTER> button.
[LAST USED] Keeps the input selected last.
[SDI1] Sets the input to SDI1.
[SDI2] Sets the input to SDI2.
[SDI3] Sets the input to SDI3.
[SDI4] Sets the input to SDI4.
[DIGITAL LINK] Sets the input to DIGITAL LINK.
[HDMI1 [SLOT1]]
*1
Sets the input to HDMI1 of the Interface Board.
[HDMI2 [SLOT1]]
*1
Sets the input to HDMI2 of the Interface Board.
[HDMI3 [SLOT2]]
*2
Sets the input to HDMI3 of the Interface Board.
[HDMI4 [SLOT2]]
*2
Sets the input to HDMI4 of the Interface Board.
[DVI-D1 [SLOT1]]
*1
Sets the input to DVI-D1 of the Interface Board.
[DVI-D2 [SLOT1]]
*1
Sets the input to DVI-D2 of the Interface Board.
[DVI-D3 [SLOT2]]
*2
Sets the input to DVI-D3 of the Interface Board.
[DVI-D4 [SLOT2]]
*2
Sets the input to DVI-D4 of the Interface Board.
[SDI1 [SLOT1]]
*1
Sets the input to SDI1 of the Interface Board.
[SDI2 [SLOT1]]
*1
Sets the input to SDI2 of the Interface Board.
[SDI3 [SLOT2]]
*2
Sets the input to SDI3 of the Interface Board.
[SDI4 [SLOT2]]
*2
Sets the input to SDI4 of the Interface Board.
[INPUT1] - [INPUT10]
*3
Sets the input to DIGITAL LINK, and switches the input of the Panasonic twisted-pair-cable
transmitter to the specied input.
*1 This can be set when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This can be set when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reected from [INPUT1] to [INPUT10]. When an item that does not reect the input name is selected, it will be disabled.