Chapter 4 Settings — [PROJECTOR SETUP] menu
162 - ENGLISH
[COMMAND]
Detailed settings of
[COMMAND]
Description
[POWER ON] ― Switches on the projector.
[STANDBY] ― Enters standby.
[SHUTTER]
[OPEN] Disables the shutter function (shutter: open).
[CLOSE] Enables the shutter function (shutter: closed).
[INPUT]
[SDI1] Switches the input to SDI1.
[SDI2] Switches the input to SDI2.
[SDI3] Switches the input to SDI3.
[SDI4] Switches the input to SDI4.
[DIGITAL LINK] Switches the input to DIGITAL LINK.
[HDMI1 [SLOT1]]
*1
Switches the input to HDMI1 of the Interface Board.
[HDMI2 [SLOT1]]
*1
Switches the input to HDMI2 of the Interface Board.
[HDMI3 [SLOT2]]
*2
Switches the input to HDMI3 of the Interface Board.
[HDMI4 [SLOT2]]
*2
Switches the input to HDMI4 of the Interface Board.
[DVI-D1 [SLOT1]]
*1
Switches the input to DVI-D1 of the Interface Board.
[DVI-D2 [SLOT1]]
*1
Switches the input to DVI-D2 of the Interface Board.
[DVI-D3 [SLOT2]]
*2
Switches the input to DVI-D3 of the Interface Board.
[DVI-D4 [SLOT2]]
*2
Switches the input to DVI-D4 of the Interface Board.
[SDI1 [SLOT1]]
*1
Switches the input to SDI1 of the Interface Board.
[SDI2 [SLOT1]]
*1
Switches the input to SDI2 of the Interface Board.
[SDI3 [SLOT2]]
*2
Switches the input to SDI3 of the Interface Board.
[SDI4 [SLOT2]]
*2
Switches the input to SDI4 of the Interface Board.
[INPUT1] - [INPUT10]
*3
Switches the input to DIGITAL LINK, and switches the input of the
Panasonic twisted-pair-cable transmitter to the specied input.
[OPERATING MODE]
*4
[HIGH]
The life of the light source shortens compared to [NORMAL], but the
luminance increases more than [NORMAL].
[NORMAL] Prioritizes luminance. (Factory default setting)
[LONG LIFE1]
Controls the power to increase the life of the light source although
the luminance is lower than that of [NORMAL].
[LONG LIFE2]
Controls the power to increase the life of the light source although
the luminance is even lower than that of [LONG LIFE1].
[LONG LIFE3]
Controls the power to increase the life of the light source to the
maximum although the luminance is even lower than that of [LONG
LIFE2].
[USER1] Controls the power with the setting set to [USER1].
[USER2] Controls the power with the setting set to [USER2].
[USER3] Controls the power with the setting set to [USER3].
[MULTI DISPLAY]
[OFF] Does not use the multi-display function.
[USER1] Displays four-screen display with the setting in [USER1].
[USER2] Displays four-screen display with the setting in [USER2].
[USER3] Displays four-screen display with the setting in [USER3].
*1 This can be set when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This can be set when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reected from [INPUT1] to [INPUT10]. When an item that does not reect the input name is selected, it will be disabled.
*4 If you change the settings while using the projector, the duration until the light source luminance decreases by half may shorten or the
luminance may decrease.
11) Press the <ENTER> button.
f The command is xed and n is displayed at the left of the selected command.
f After the command is xed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 160)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
To Next Page
Loading...
