Panasonic PT-RQ32K

Chapter 7 Appendix — Technical information
ENGLISH - 245
Signal name
(SIGNAL FORMAT)
Resolution
(Dots)
Scanning freq.
Dot clock
freq.
(MHz)
Compatible signal
Horizontal
(kHz)
Vertical
(Hz)
DIGITAL
LINK
HDMI
*1
DVI-D
*2
1 1 2 3 1 2 3
1680 x 1050/60 1 680 x 1 050 65.3 60.0 146.3
l l
― ―
l
― ―
1920 x 1080/50 1 920 x 1 080 55.6 49.9 141.5
l l
― ―
l
― ―
1920 x 1080/60
1 920 x 1 080
*5
66.6 59.9 138.5
l l
― ―
l
― ―
1 920 x 1 080 67.2 60.0 173.0
l l
― ― ― ― ―
1920 x 1200/50 1 920 x 1 200 61.8 49.9 158.3
l l
― ―
l
― ―
1920 x 1200/60 1 920 x 1 200 74.6 59.9 193.3
l l
― ― ― ― ―
1920 x 1200/60RB 1 920 x 1 200
*5
74.0 60.0 154.0
l l
― ―
l
― ―
2560 x 1600/50 2 560 x 1 600 82.4 50.0 286.0
l l
― ― ― ― ―
2560 x 1600/60 2 560 x 1 600
*5
98.7 60.0 268.5
l l
― ― ― ― ―
3840 x 2400/30 3 840 x 2 400
*5
73.0 30.0 286.2
l l
― ― ― ― ―
3840 x 2400/60 3 840 x 2 400 148.1 60.0 616.0 ― ― ―
l
― ―
l
3840 x 2400/60 3 840 x 2 400
*5
148.1 60.0 592.5 ―
l
― ― ― ― ―
3840 x 2400/50 3 840 x 2 400 123.6 49.9 633.0 ― ― ―
l
― ―
l
3840 x 2400/50 3 840 x 2 400
*5
122.9 50.0 481.6 ―
l
― ― ― ― ―
*1 This is supported when the optional Interface Board for HDMI 2 input (Model No.: ET-MDNHM10) is installed in the slot.
Quad link is supported only when the optional Interface Board for HDMI 2 input (Model No.: ET-MDNHM10) is installed on both <SLOT 1> and
<SLOT 2>.
*2 This is supported when the optional Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10) is installed in the slot.
Quad link is supported only when the optional Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10) is installed on both <SLOT 1> and
<SLOT 2>.
*3 Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
*4 YP
B
P
R
4:2:0 format only
*5 VESA CVT-RB (Reduced Blanking)-compliant
Note
f A signal with a different resolution is converted to the number of display dots. The number of display dots is as follows.
g When the [ADVANCED MENU] menu → [QUAD PIXEL DRIVE] is set to [ON]: 5 120 x 3 200
g When the [ADVANCED MENU] menu → [QUAD PIXEL DRIVE] is set to [OFF]: 2 560 x 1 600
f The “i” at the end of the resolution indicates an interlaced signal.
f When interlaced signals are connected, ickering may occur on the projected image.