26
VQT4E52
Preparation
≥ Turn off all other Panasonic products.
≥ Turn on this system.
Change the remote control code to code 2:
1
Aim the remote control at this system’s remote control
sensor.
2 Press and hold [MUTE] and [BD/DVD] on the
remote control for more than 4 sec.
≥ All the indicators will blink for 10 sec when the code of
this system is changed.
≥ The setting is maintained until it is changed again.
≥ If this system does not operate after changing the code,
repeat steps 1 and 2.
≥ To change the remote control code to code 1, repeat the
steps above, but replace [BD/DVD] with [TV].
∫ To reduce the clear-mode dialog
effect
When the dialog does not sound natural while the
volume is set low, for example, it is possible to reduce
the dialog enhancing effect as follows:
Press and hold [TV] on the remote control and [s VOL]
on the active subwoofer for more than 2 sec.
∫ To turn off VIERA Link “HDAVI
Control”
When “HDAVI Control” compatible equipment does not
work well with this system, for example, it is possible to
turn off this function as follows:
≥ When VIERA Link is turned off the ARC function is not
available. Be sure to connect the optical digital audio
cable. (> 19)
1
Press and hold [MUTE] on the remote control and
[
s
VOL] on the active subwoofer for more than 2 sec.
2 After the setting has changed, turn off all the
connected devices and then turn them on again.
∫ To turn off the volume limitation
If a state of the lowered volume disturbs you every time
this system turns on, for example, it is possible to turn off
this function as follows:
Press and hold [MUTE] on the remote control and
[VOL r] on the active subwoofer for more than 2 sec.
The settings of the clear-mode dialog effect, VIERA Link
“HDAVI Control”, and the volume limitation remain intact
even if you switch this system to standby mode. To turn these
3 functions back on, this system must be set back to the
factory preset. (> right)
≥ All the indicators will blink once when the setting is
changed.
Reference
Troubleshooting
Before requesting service, make the following
checks. If you are in doubt about some of the
check points, or if the solutions indicated in the
following guide do not solve the problem, consult
your dealer for instructions.
No power.
≥ Insert the AC mains lead securely. (> 20)
≥
After turning this system on, if the indicators blink
and this system immediately turns off, unplug the
AC mains lead and consult your dealer.
The remote control does not work properly.
≥ The battery is depleted. Replace it with a new
one. (> 7)
≥
It is possible that the insulation sheet has not been
removed. Remove the insulation sheet. (
>
7)
≥ It may be necessary to set the code of the
remote control again after changing the battery
of the remote control. (> 25)
≥ Use the remote control within the correct
operation range. (> 9)
The “TV” indicator blinks, but there is no sound.
Remove the AC mains lead and consult your dealer.
If there are any other indicators blinking, be sure to
inform the blinking indicators to your dealer.
This system is automatically switched to
standby mode.
The auto standby function is on. This system will
automatically switch to standby mode when no signal
is input and no operation is performed for approx.
2 hours. Refer to page 25 to turn this function off.
This system is turned off when the TV’s
speakers are selected in the speaker control.
This is a normal feature when using VIERA Link
(HDAVI Control 4 or later). For details please
read the operating instructions for the TV on its
power save feature. (> 24)
To return to the factory preset.
While this system is on, press [Í/I] on the
active subwoofer for more than 4 sec.
(All the indicators will blink twice when the
active subwoofer is reset.)
If the system does not operate as expected,
returning the settings to the factory preset
may solve the problem.
≥ The remote control code will return to “1”
when this system is returned to the factory
preset. To change the remote control code,
refer to page 25.
General operation
SC-HTB20EBEGGNGS_VQT4E52.book 26 ページ ２０１２年２月２４日 金曜日 午後７時５１分
To Next Page
Loading...
Need help?
General
Weight and Dimensions
