Parker Hyperchill Plus-E ICEP 080E - Page 35

English
13/20
ICEP080E-ICEP120E
4.6.2 Temperature control “&03”
Temperature control setting
Switch ON the chiller “ON” using the Main disconnector switch QS,
and wait on display the indication “OFF”.
Press the buttons “
esc
” “
set
” together to enter on “D” parame-
ters.
esc
set
F1
F3
F2
1
2
3
1
2 3
2))
2))
Parameter “3$U” appears.
Press the button “
set
” to enter.
esc
set
F1
F3
F2
1
2
3
1
2 3
3$U
3$U
Parameter “&IJ” appears.
Use the buttons “
”and “ ” to select “&03” parameter.
esc
set
F1
F3
F2
1
2
3
1
2 3
&)
&)
Press the button “
set
” to enter.
esc
set
F1
F3
F2
1
2
3
1
2 3
&03
&03
Parameter “6(W” appears.
Press the button “
set
” to enter.
esc
set
F1
F3
F2
1
2
3
1
2 3
6(W
6(W
The default value is “13.0”
Use the buttons “
”and “ ” to change the value.
esc
set
F1
F3
F2
1
2
3
1
2 3
13.0
13.0
Press the button “
set
” to confi rm.
esc
set
F1
F3
F2
1
2
3
1
2 3
15.0
15.0
The parameter has now been stored.
Press the button “
esc
” to exit, three time.
esc
set
F1
F3
F2
1
2
3
1
2 3
6(W
6(W
Important: A set of temperautre between 1°C and 5°C, must be done by specialised technicians that
must use the specifi c service manual of this product.
Temperature control differential setting
Switch ON the chiller “ON” using the Main disconnector switch QS,
and wait on display the indication “OFF”.
Press the buttons “
esc
” “
set
” together to enter on “D” parame-
ters.
esc
set
F1
F3
F2
1
2
3
1
2 3
2))
2))
Parameter “3$U” appears.
Press the button “
set
” to enter.
esc
set
F1
F3
F2
1
2
3
1
2 3
3$U
3$U
Parameter “&IJ” appears.
Use the buttons “
”and “ ” to select “&03” parameter.
esc
set
F1
F3
F2
1
2
3
1
2 3
&)
&)
Press the button “
set
” to enter.
esc
set
F1
F3
F2
1
2
3
1
2 3
&03
&03
Parameter “6(W” appears.
Use the buttons “
”and “ ” to select “'L)” parameter.
esc
set
F1
F3
F2
1
2
3
1
2 3
6HW
6HW
Press the button “
set
” to enter.
esc
set
F1
F3
F2
1
2
3
1
2 3
GL)
GL)
The default value is “4.0”
Use the buttons “
”and “ ” to change the value.
esc
set
F1
F3
F2
1
2
3
1
2 3
4.0
4.0
Press the button “
set
” to confi rm.
esc
set
F1
F3
F2
1
2
3
1
2 3
3.0
3.0
The parameter has now been stored.
Press the button “
esc
” to exit, three time.
esc
set
F1
F3
F2
1
2
3
1
2 3
GL)
GL)